IBM P260 Installation And Service Manual Download Page 362

Page: 362 / 524

2640-131

Explanation:

Smart status threshold exceeded. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2640

2640-132

Explanation:

Command timeouts threshold exceeded. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2640

2640-133

Explanation:

Command timeout with error condition. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2640

2640-134

Explanation:

Hardware command or DMA failure. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2640

2640-136

Explanation:

Timeout waiting for controller or drive with no busy status. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2640

FFC_2631

2640-131 • 2640-136

350

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands