IBM P260 Installation And Service Manual Download Page 323

Page: 323 / 524

652-613

Explanation:

A non-critical error has been detected: external cache ECC single-bit error. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_D01

652-623

Explanation:

A non-critical error has been detected: correctable error threshold exceeded. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2C6

652-630

Explanation:

A non-critical error has been detected: I/O expansion bus parity error. Schedule deferred maintenance.

Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_307

652-631

Explanation:

A non-critical error has been detected: I/O expansion bus time-out error. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_307

652-632

Explanation:

A non-critical error has been detected: I/O expansion bus connection failure. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_307

652-613 • 652-632

Chapter 8. Troubleshooting

311

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands