manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

110-XXXX

Explanation:

The system halted while diagnostics were executing.

Note: xxxx corresponds to the last three or four digits of the SRN following the dash (-).

1.

If your 110 SRN is not listed, substitute the last three or four digits of the SRN for xxxx and go to Failing function
codes to identify the failing feature.

2.

Run stand-alone diagnostics and the problem determination procedure for your operating system.

Response:

Failing Item:

v

FFC_XXXX

v

FFC_221

252B-101

Explanation:

Adapter configuration error.

1.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

2.

Replace any parts reported by the diagnostic program.

3.

Replace the system-board

Response:

Failing Item:

v

FFC_252B

252B-710

Explanation:

Permanent adapter failure.

1.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

2.

Replace any parts reported by the diagnostic program.

3.

Replace the system-board

Response:

Failing Item:

v

FFC_252B

252B-711

Explanation:

Adapter failure.

1.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

2.

Replace any parts reported by the diagnostic program.

3.

Replace the system-board

Response:

Failing Item:

v

FFC_252B

110-XXXX • 252B-711

326

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

IBM ThinkVision L200p User Manual preview
ThinkVision L200p
Brand: IBM Pages: 32
EBN Technology SPPC70-5B-C1G Service Manual preview
SPPC70-5B-C1G
Brand: EBN Technology Pages: 20
iHealth Track KN550-BT User Manual preview
Track KN550-BT
Brand: iHealth Pages: 14
Wells-Gardner D9100 Series Service Manual preview
D9100 Series
Brand: Wells-Gardner Pages: 25
IEE 03875-06-0114 Reference Manual preview
03875-06-0114
Brand: IEE Pages: 22
Valor TPMS-203 User Manual preview
TPMS-203
Brand: Valor Pages: 11
Microtek C997SD User Manual preview
C997SD
Brand: Microtek Pages: 25
Citizen CH-618 Instruction Manual preview
CH-618
Brand: Citizen Pages: 60
Welch Allyn ProBP 2000 Directions For Use Manual preview
ProBP 2000
Brand: Welch Allyn Pages: 39
Parker 71-113 Series Assembly Instructions preview
71-113 Series
Brand: Parker Pages: 4
Barco MDRC­-2124 TS Specifications preview
MDRC­-2124 TS
Brand: Barco Pages: 4
ViewSonic VX2257-mhd User Manual preview
VX2257-mhd
Brand: ViewSonic Pages: 26
IFM Electronic efector300 SI0513 Operating Instructions Manual preview
efector300 SI0513
Brand: IFM Electronic Pages: 52
Samsung S27E370 User Manual preview
S27E370
Brand: Samsung Pages: 78
Samsung S27D590P User Manual preview
S27D590P
Brand: Samsung Pages: 92
Samsung S19E410HY User Manual preview
S19E410HY
Brand: Samsung Pages: 112
Samsung S24D300B User Manual preview
S24D300B
Brand: Samsung Pages: 120
Samsung S19E200NW Manual preview
S19E200NW
Brand: Samsung Pages: 146

Brands by name

Popular brands

Load more brands