manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

a.

Select Diagnostic Routines and press Enter.

b.

From the Diagnostic Mode Selection menu, select System Verification.

c.

Select the resource to be tested, and press F7=Commit.

d.

Record any results provided and go to “Service request numbers (SRNs)” on page 301 to
identify the failure and perform the action(s).

e.

When testing is complete, press F3 to return to the Diagnostic Selection menu. If you want to
run another test, press F3 again to return to the Function Selection menu.

v

Task selection

a.

Select Task Selection and press Enter.

b.

Select the task to be run and press Enter.

c.

If the Resource Selection List menu is displayed, select the resource on which the task is to be
run and press F7=Commit.

d.

Follow the instruction for the selected task.

e.

When the task is complete, press F3 to return to the Task Selection List menu. If you want to
run another test, press F3 again to return to the Function Selection menu.

3.

When testing is complete, press F3 until the Diagnostic Operating Instructions window is displayed.
Then press F3 again to exit the diagnostic program.

Boot problem resolution

Depending on the boot device, a checkpoint might be displayed in the list of checkpoints in the
management console for an extended period of time while the boot image is retrieved from the device.

About this task

This situation is particularly true for boot image and network boot attempts.

Note:

For network boot attempts, if the system is not connected to an active network, or if there is no

compute node configured to respond to the system's boot request, the system will still attempt to boot.
Because time-out durations are necessarily long to accommodate retry operations, the system might
appear to be hung.

If you suspect a problem loading the boot image, complete the following steps:

Procedure

1.

Make sure that your boot list is correct.

a.

Use the management console to display the boot sequences for the compute nodes in your IBM
Flex System Enterprise Chassis.

b.

Find your compute node on the list that is displayed and make sure that the device from which
you are attempting to boot is the first device in the boot sequence. If it is not, select your compute
node from the list of compute nodes and change the boot sequence. Power off and then power on
your compute node to retry the boot.

Note:

If Network is selected, the compute node tries to boot from both Ethernet ports on the

system board.

c.

If this boot attempt fails, complete the following steps:

1)

If you are attempting to boot from the network, go to Step 2.

2)

If you are attempting to boot from a hard disk drive, go to Step 3.

456

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

iHealth BP3 User Manual preview
BP3
Brand: iHealth Pages: 12
iHealth BP3 Quick Start Manual preview
BP3
Brand: iHealth Pages: 2
Samsung SyncMaster 2023 NW User Manual preview
SyncMaster 2023 NW
Brand: Samsung Pages: 68
Samsung SyncMaster 720B User Manual preview
SyncMaster 720B
Brand: Samsung Pages: 78
iHealth Track KN550-BT User Manual preview
Track KN550-BT
Brand: iHealth Pages: 14
schmersal ASM E1-R2 Operating Instructions Manual preview
ASM E1-R2
Brand: schmersal Pages: 6
Iiyama TF3237MC User Manual preview
TF3237MC
Brand: Iiyama Pages: 29
Baaske Medical e-medic 19AM User Manual preview
e-medic 19AM
Brand: Baaske Medical Pages: 32
Gateway HX2000 User Manual preview
HX2000
Brand: Gateway Pages: 26
ViewSonic G90f (Finnish) Käyttöopas preview
G90f
Brand: ViewSonic Pages: 19
I-Tech HAP-19AV Series User Manual preview
HAP-19AV Series
Brand: I-Tech Pages: 28
ViewSonic G90FB Specification Sheet preview
G90FB
Brand: ViewSonic Pages: 2
AOC FT720 Technical Specifications preview
FT720
Brand: AOC Pages: 1
OMG Giotto V3 Installation Manual preview
Giotto V3
Brand: OMG Pages: 36
AOC 7F-SLK User Manual preview
7F-SLK
Brand: AOC Pages: 17
Microlife BP A3L Comfort Manual preview
BP A3L Comfort
Brand: Microlife Pages: 87
Elo TouchSystems 1915L User Manual preview
1915L
Brand: Elo TouchSystems Pages: 37
Magene HRM30 Manual preview
HRM30
Brand: Magene Pages: 19

Brands by name

Popular brands

Load more brands