IBM P260 Installation And Service Manual Download Page 429

Page: 429 / 524

2506-9051

Explanation:

Cache data exists for one or more missing/failed disks. Go to Performing the checkout procedure.

Response:

2506-9052

Explanation:

Cache data exists for one or more modified disks. Go to Performing the checkout procedure.

Response:

2506-9054

Explanation:

RAID controller resources not available due to previous problems. Go to Performing the checkout

procedure.

Response:

2506-9060

Explanation:

One or more disk pairs are missing from a RAID-10 Disk Array. Go to Performing the checkout

procedure.

Response:

2506-9061

Explanation:

One or more disks are missing from a RAID-0 Disk Array. Go to Performing the checkout procedure.

Response:

2506-9062

Explanation:

One or more disks are missing from a RAID-0 Disk Array. Go to Performing the checkout procedure.

Response:

2506-9063

Explanation:

Maximum number of functional Disk Arrays has been exceeded. Go to Performing the checkout

procedure.

Response:

2506-9073

Explanation:

Multiple controllers connected in an invalid configuration. Go to Performing the checkout procedure.

Response:

2506-9051 • 2506-9073

Chapter 8. Troubleshooting

417

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands