IBM P260 Installation And Service Manual Download Page 265

Page: 265 / 524

C200211F

Explanation:

Power on command successful

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C20021FF

Explanation:

Power on phase complete

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C2002200

Explanation:

Begin acquiring slot locks

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C20022FF

Explanation:

End acquiring slot locks

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C2002300

Explanation:

Begin acquiring VIO slot locks

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C20023FF

Explanation:

End acquiring VIO slot locks

Response:

Go to Recovering the system firmware.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

C200211F • C20023FF

Chapter 8. Troubleshooting

253

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands