IBM P260 Installation And Service Manual Download Page 329

Page: 329 / 524

815-101

Explanation:

Floating point processor failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_815

815-102

Explanation:

Floating point processor failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_815

815-200

Explanation:

Power-on self-test indicates a processor failure. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_815

FFC_7C0

815-201

Explanation:

Processor has a status of failed. Processors with a failed status are deconfigured and therefore cannot

be tested or used by the system. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_815

817-123

Explanation:

The I/O planar time-of-day clock test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_817

815-101 • 817-123

Chapter 8. Troubleshooting

317

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands