manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

a.

Enter the system type, which is the value of the sys_type field from the IVM or the System type
field from the ASMI, HMC, or FSM.

b.

Enter the serial number, which is the value of the sys_serial_num from the IVM or the System
serial number

field from the ASMI, HMC, or FSM.

If the code has not yet been assigned, then the following note is displayed:

No matching activation code found.

Otherwise, look for a VET entry with a date that aligns with your request date. Then, record the
corresponding VET activation code.

5.

Enter the VET activation code to activate PowerVM virtualization through one of the following
methods:

v

For ASMI, HMC, or IVM graphical user interface (GUI), see http://www.ibm.com/support/entry/
portal/docdisplay?lndocid=MIGR-5091991.

v

For FSM, see http://www.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5091991.

v

For IVM command-line interface (CLI), complete the following steps:

a.

In an IVM session, enter the following command to activate the 34-character VET activation
code.

chvet -o e -k <activation_code>

Where, <activation_code> is the Activation Code.
For example, if the activation code is

4D8D6E7A81409365CA1F000028200041FD

, enter the following

command:

chvet -o e -k 4D8D6E7A81409365CA1F000028200041FD

b.

In  an  IVM  session,  validate  that  the  code  entry  is  successful  by  using  the 

lsvet -t hist

command.
The following is an example of the command output:

time_stamp=03/06/2013 16:25:08,"entry=[VIOSI05000400-0331] CoD advanced
functions activation code entered, resource ID: CA1F, capabilities: 2820."
time_stamp=03/06/2013 16:25:08,entry=[VIOSI05000403-0332] Virtual I/O server
capability enabled.
time_stamp=03/06/2013 16:25:08,entry=[VIOSI05000405-0333] Micro-partitioning
capability enabled.

This ends the procedure.

The procedure does not require you to restart the compute node to activate the PowerVM virtualization
functions.

Note:

If you intend to restart the compute node after you complete this procedure, wait at least 5

minutes before you restart the compute node, or before you power off and power on the compute node.
This is to ensure that the activation code is stored in the vital product data on the management card.

80

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

A&D UB-511 Instruction Manual preview
UB-511
Brand: A&D Pages: 16
A&D UB-510 Operational Manual preview
UB-510
Brand: A&D Pages: 50
A&D UA-852 Manuale Di Istruzioni preview
UA-852
Brand: A&D Pages: 20
A&D UA-767 Manuel D'Instructions preview
UA-767
Brand: A&D Pages: 14
A&D UA-705 Quick Start Card preview
UA-705
Brand: A&D Pages: 3
A&D UA-621 Operation Manual preview
UA-621
Brand: A&D Pages: 42
A&D UA-1030T Specification preview
UA-1030T
Brand: A&D Pages: 2
A&D ESSENTIAL UB-525 Instruction Manual preview
ESSENTIAL UB-525
Brand: A&D Pages: 48
Daktronics Galaxy AF-3165 Display Manual preview
Galaxy AF-3165
Brand: Daktronics Pages: 97
Sanitas SBM 21 Manual preview
SBM 21
Brand: Sanitas Pages: 33
Sanitas SBM 03 Instructions For Use Manual preview
SBM 03
Brand: Sanitas Pages: 60
Sanitas SBC 53 Instructions For Use Manual preview
SBC 53
Brand: Sanitas Pages: 96
Sanitas SBC 24 Instructions For Use Manual preview
SBC 24
Brand: Sanitas Pages: 52
Alecto DOS-150 Instruction Manual preview
DOS-150
Brand: Alecto Pages: 25
Waeco Mobitronic RV-RMM-56 Installation And Operating Instructions Manual preview
Mobitronic RV-RMM-56
Brand: Waeco Pages: 87
Uniden BW614PTR Owner'S Manual preview
BW614PTR
Brand: Uniden Pages: 24
Apantac TAHOMA MiniQ Hardware Manual preview
TAHOMA MiniQ
Brand: Apantac Pages: 31
Westinghouse LCM-15V5 User Manual preview
LCM-15V5
Brand: Westinghouse Pages: 15

Brands by name

Popular brands

Load more brands