manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

B7000441

Explanation:

Service processor failure. The platform encountered an error early in the startup or termination

process.

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7000443

Explanation:

Service processor failure.

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7000601

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

Note: This code and associated data can be used to determine why the time of day for a partition was lost.

B7000602

Explanation:

System firmware detected an error condition.

Response:

1.

Collect the event log information.

2.

Go to Isolating firmware problems.

B7000611

Explanation:

There is a problem with the system hardware clock; the clock time is invalid.

Response:

Use the operating system to set the system clock.

B7000621

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B7000641

Explanation:

System firmware detected an error.

Response:

1.

Collect the platform dump information.

2.

Go to Isolating firmware problems.

B7000441 • B7000641

Chapter 8. Troubleshooting

171

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

babymoov A014409 Quick Start Manual preview
A014409
Brand: babymoov Pages: 2
M-system B6U-LCD Instruction Manual preview
B6U-LCD
Brand: M-system Pages: 2
Aspect BIS VIEW Service Information Manual preview
BIS VIEW
Brand: Aspect Pages: 100
TRANSTEK TMB-2088-T User Manual preview
TMB-2088-T
Brand: TRANSTEK Pages: 19
Iiyama ProLite L460W User Manual preview
ProLite L460W
Brand: Iiyama Pages: 36
Inspire IMC-734 Owner'S Manual preview
IMC-734
Brand: Inspire Pages: 24
Envision EFT920 User Manual preview
EFT920
Brand: Envision Pages: 14
Genie LM215 User Manual preview
LM215
Brand: Genie Pages: 11
ViewSonic VA2408-H User Manual preview
VA2408-H
Brand: ViewSonic Pages: 44
Voyager VOM74WP Owner'S Manual preview
VOM74WP
Brand: Voyager Pages: 58
NEC MultiSync E241N User Manual preview
MultiSync E241N
Brand: NEC Pages: 22
NEC R 37 Xtra User Manual preview
R 37 Xtra
Brand: NEC Pages: 38
NEC MultiSync XP29, XM29 Xtra User Manual preview
MultiSync XP29, XM29 Xtra
Brand: NEC Pages: 40
NEC XV2930 User Manual preview
XV2930
Brand: NEC Pages: 16
NEC MultiSync EA271Q-WH User Manual preview
MultiSync EA271Q-WH
Brand: NEC Pages: 39
NEC MultiSync M981 User Manual preview
MultiSync M981
Brand: NEC Pages: 113
Diamond View DV17NF User Manual preview
DV17NF
Brand: Diamond View Pages: 24
TPS miniCHEM-Sal Manual preview
miniCHEM-Sal
Brand: TPS Pages: 31

Brands by name

Popular brands

Load more brands