IBM P260 Installation And Service Manual Download Page 161 | Manualshive

Page: 161 / 524

background image

B2001260

Explanation:

A problem occurred during the startup of a partition.

The partition could not start at the Timed Power On setting because the partition was not set to Normal.

Response:

Set the partition to Normal.

B2001265

Explanation:

The partition could not start up. An operating system Main Storage Dump startup was attempted with

the startup side on D-mode, which is not a valid operating system startup scenario. The startup will be halted. This
SRC can occur when a D-mode SLIC installation fails and attempts a Main Storage Dump.

Response:

Correct the startup settings.

B2001266

Explanation:

The partition could not start up. You are attempting to start up an operating system that is not

supported.

Response:

Install a supported operating system and restart the partition.

B2001280

Explanation:

A problem occurred during a partition Main Storage Dump. A mainstore dump startup did not

complete due to a configuration mismatch.

Response:

Go to Isolating firmware problems.

B2001281

Explanation:

A partition memory error occurred. The failed memory will no longer be used.

Response:

Restart the partition.

B2001282

Explanation:

A problem occurred during the startup of a partition.

Response:

Go to Isolating firmware problems.

B2001320

Explanation:

A problem occurred during the startup of a partition.

No default load source was selected. The startup will attempt to continue, but there may not be enough information
to find the correct load source.

Response:

Configure a load source for the partition. Then restart the partition.

B2001260 • B2001320

Chapter 8. Troubleshooting

149

«
...
159
160
161
162
163
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: GE Pages: 24

Corometrics 250cx Series

Brand: GE Pages: 250

SyncMaster S23A550H

Brand: Samsung Pages: 61

Dual Belt Bluetooth Smart / ANT+

Brand: GEONAUTE Pages: 5

Brand: Aaeon Pages: 47

Brand: YEYIAN Pages: 32

Brand: Daewoo Pages: 27

IS-UM17 B Series

Brand: Hope Industrial Systems Pages: 24

Brand: Hanns.G Pages: 23

Brand: Barco Pages: 91

migra MPB EN TCP/IP

Brand: microSYST Pages: 51

Brand: Rockwell Automation Pages: 64

Brand: Hanns.G Pages: 1

Brand: iameco Pages: 38

Brand: LCD4Video Pages: 15

LC-M27-FHD-240-C

Brand: LC-POWER Pages: 63

Brand: Mitsubishi Pages: 55

Brand: Barco Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands