IBM P260 Installation And Service Manual Download Page 158 | Manualshive

Page: 158 / 524

background image

B1818BC2

Explanation:

The service processor was reset due to a communication failure with the Chassis Management Module.

Response:

If this is tracking event, no service action is required. Otherwise look for Chassis Management Module

problems and resolve them.

B181D548

Explanation:

An informational event was generated on the service processor.

Response:

This is an informational tracking event and no service action is required.

B2xxyyyy logical partition SRCs:

A B2xxyyyy SRC is a logical partition reference code that is related to logical partitioning.

The B2xxyyyy SRCs below are the system reference codes that might be displayed if system firmware
detects a problem. Follow the suggested actions in the order in which they are listed until the problem is
solved. If an action solves the problem, then you can stop performing the remaining actions. See
Chapter 7, “Parts listing for IBM Flex System p260 and p460 Compute Nodes,” on page 97 to determine
which components are CRUs and which components are FRUs.

Note:

For problems persisting after completing the suggested actions, see “Checkout procedure” on page

451 and “Solving undetermined problems” on page 498.

B2001020

Explanation:

Firmware for the specified function cannot be loaded

The firmware resource and all associated virtual and/or physical devices will not be available until the issue is
resolved.

Response:

Collect a platform dump and then go to Isolating firmware problems.

B2001130

Explanation:

A problem occurred during the migration of a partition

You attempted to migrate a partition to a system that has a power or thermal problem. The migration will not
continue.

Response:

Look for and fix power or thermal problems and then retry the migration.

B2001131

Explanation:

A problem occurred during the migration of a partition.

The migration of a partition did not complete.

Response:

Check for server firmware updates; then, install the updates if available.

B1818BC2 • B2001131

146

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
156
157
158
159
160
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: Acer Pages: 13

Brand: Acer Pages: 2

Brand: Acer Pages: 2

Brand: Acer Pages: 20

Brand: Daktronics Pages: 29

Brand: Ebird Pages: 11

Brand: NB Pages: 14

Brand: IBM Pages: 147

Brand: Samsung Pages: 95

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

SyncMaster 570S TFT

Brand: Samsung Pages: 30

Brand: Samsung Pages: 45

Brand: Samsung Pages: 79

Brand: Samsung Pages: 70

SyncMaster BN59-00954A_02

Brand: Samsung Pages: 21

SyncMaster BX2035

Brand: Samsung Pages: 47

SyncMaster LD190

Brand: Samsung Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands