manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

Results

If these steps do not resolve the problem, it is probably a problem with the compute node. See
“Connectivity problems” on page 459 for more information.

Solving shared power problems

Problems with shared resources might appear to be in the compute node, but might actually be a
problem in a IBM Flex System Enterprise Chassis power component.

About this task

To check the general function of shared power resources, complete the following steps:

Procedure

1.

Verify that the LEDs on all the power modules of the IBM Flex System Enterprise Chassis are lit.

2.

Verify that power is being supplied to the IBM Flex System Enterprise Chassis.

3.

Verify that the installation of the compute node type is supported by the IBM Flex System Enterprise
Chassis.

4.

Verify that the power configuration of the IBM Flex System Enterprise Chassis supports the bay
where your compute node is installed.

5.

Verify that the power management configuration and status of the IBM Flex System Enterprise
Chassis support compute node operation.
See the information center for your management module or the Management Module User's Guide or
the Management Module Command-Line Interface Reference Guide for more information.

6.

Verify that the local power control for the compute node is set correctly.
See the information center for your management module or the Management Module User's Guide or
the Management Module Command-Line Interface Reference Guide for more information.

7.

Verify that the IBM Flex System Enterprise Chassis blowers are correctly installed and operational.

Solving undetermined problems

When you are diagnosing a problem in the IBM Flex System p260 Compute Node or IBM Flex System
p460 Compute Node, you must determine whether the problem is in the compute node or in the IBM
Flex System Enterprise Chassis.

About this task

v

If all of the compute nodes have the same symptom, it is probably a problem in the IBM Flex System
Enterprise Chassis.
For more information, see the following documentation:
– Hardware Maintenance Manual and Troubleshooting Guide for your IBM Flex System Enterprise Chassis
– Problem Determination and Service Guide for your IBM Flex System Enterprise Chassis

v

If the IBM Flex System Enterprise Chassis contains more than one compute node and only one of the
compute nodes has the problem, troubleshoot the compute node that has the problem.

Check the LEDs on all the power supplies of the IBM Flex System Enterprise Chassis where the compute
node is installed. If the LEDs indicate that the power supplies are working correctly, and powering off
and powering on the compute node does not correct the problem, complete the following steps:

Procedure

498

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Samsung QM85F Quick Setup Manual preview
QM85F
Brand: Samsung Pages: 2
Raymarine i70 Quick Reference preview
i70
Brand: Raymarine Pages: 12
Samsung SH37F Quick Setup Manual preview
SH37F
Brand: Samsung Pages: 2
Samsung DC32E Quick Setup Manual preview
DC32E
Brand: Samsung Pages: 2
Samsung ED65E User Manual preview
ED65E
Brand: Samsung Pages: 148
Datavideo TLM-700HD Quick Start Manual preview
TLM-700HD
Brand: Datavideo Pages: 14
iBaby M3s User Manual preview
M3s
Brand: iBaby Pages: 15
Idmed ToFscan User Manual preview
ToFscan
Brand: Idmed Pages: 28
Waveshare 13.3 inch HDMI LCD (H) User Manual preview
13.3 inch HDMI LCD (H)
Brand: Waveshare Pages: 12
Samsung LS27A650DS/ZA User Manual preview
LS27A650DS/ZA
Brand: Samsung Pages: 92
CFORCE CF015Q Manual preview
CF015Q
Brand: CFORCE Pages: 15
Hartig+Helling MBF 1213 Operating Instructions Manual preview
MBF 1213
Brand: Hartig+Helling Pages: 22
Hanns.G HL205DPB Brochure & Specs preview
HL205DPB
Brand: Hanns.G Pages: 2
HANNspree Hanns G HL225PPB User Manual preview
Hanns G HL225PPB
Brand: HANNspree Pages: 20
Siebert XC420 Series Operating Instructions Manual preview
XC420 Series
Brand: Siebert Pages: 47
Rydeen BM354S Owner'S Manual preview
BM354S
Brand: Rydeen Pages: 5
Olorin VistaLine Series User Manual preview
VistaLine Series
Brand: Olorin Pages: 49
HANNspree HF207HPB User Manual preview
HF207HPB
Brand: HANNspree Pages: 23

Brands by name

Popular brands

Load more brands