IBM P260 Installation And Service Manual Download Page 194

Page: 194 / 524

B7006974

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B7006978

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B7006979

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B700697C

Explanation:

Connection from service processor to system processor failed.

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006980

Explanation:

RIO, HSL or 12X controller failure

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006981

Explanation:

System bus error.

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006984

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B7006985

Explanation:

Remote I/O (RIO), high-speed link (HSL), or 12X loop status message.

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006974 • B7006985

182

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands