IBM P260 Installation And Service Manual Download Page 374

Page: 374 / 524

26D2-102

Explanation:

An unrecoverable media error occurred. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-104

Explanation:

The motor failed to restart. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-105

Explanation:

The drive did not become ready. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-106

Explanation:

The electronics card test failed. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-108

Explanation:

The bus test failed. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-110

Explanation:

The media format is corrupted. Replace the 600 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_26D2

26D2-102 • 26D2-110

362

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands