IBM P260 Installation And Service Manual Download Page 281

Page: 281 / 524

CA00E135

Explanation:

Create HCA node

Response:

Go to Checkout procedure.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

CA00E136

Explanation:

Create BSR node

Response:

Go to Checkout procedure.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

CA00E137

Explanation:

Create HEA node

Response:

Reboot the server.

If the problem persists:

Go to Checkout procedure.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

CA00E138

Explanation:

Create options node

Response:

Go to Checkout procedure.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

CA00E139

Explanation:

Create aliases node and system aliases

Response:

Go to Checkout procedure.

Replace the system-board, as described in Replacing the system-board and chassis assembly.

CA00E135 • CA00E139

Chapter 8. Troubleshooting

269

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands