IBM P260 Installation And Service Manual Download Page 368

Page: 368 / 524

268B-640

Explanation:

Error log analysis indicates a path error. Replace the 300 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

FFC_268B

26B4-102

Explanation:

An unrecoverable media error occurred. Replace the 200 GB SATA Solid State Drive.

Response:

Failing Item:

FFC_26B4

26B4-104

Explanation:

The motor failed to restart. Replace the 200 GB SATA Solid State Drive.

Response:

Failing Item:

FFC_26B4

26B4-105

Explanation:

The drive did not become ready. Replace the 200 GB SATA Solid State Drive.

Response:

Failing Item:

FFC_26B4

26B4-106

Explanation:

The electronics card test failed. Replace the 200 GB SATA Solid State Drive.

Response:

Failing Item:

FFC_26B4

26B4-108

Explanation:

The bus test failed. Replace the 200 GB SATA Solid State Drive.

Response:

Failing Item:

FFC_26B4

268B-640 • 26B4-108

356

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands