manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

268B-112

Explanation:

The diagnostic test failed. Replace the 300 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

v

FFC_268B

268B-114

Explanation:

An unrecoverable hardware error. Replace the 300 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

v

FFC_268B

268B-116

Explanation:

A protocol error.

1.

Make sure that the firmware of the FRUs shown and the parent adapter, are compatible with the diagnostic and
application software levels.

2.

If you do not find a problem, call your operating-system support person.

Response:

Failing Item:

v

FFC_268B

268B-117

Explanation:

A write-protect error occurred. Replace the 300 GB SFF SAS Hard Disk Drive.

Response:

Failing Item:

v

FFC_268B

268B-118

Explanation:

A SCSI command time-out occurred. Replace the 300 GB SFF SAS Hard Disk Drive. Run diagnostics

again on the drive. If the error repeats, replace the 2nd FRU identified by diagnostics.

Response:

Failing Item:

v

FFC_268B

v

FFC_B88

268B-112 • 268B-118

352

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Bacharach HGM-SZ Supplementary Manual preview
HGM-SZ
Brand: Bacharach Pages: 5
Sam4s SAM4POS Reference Manual preview
SAM4POS
Brand: Sam4s Pages: 76
Waveshare 13.3 inch HDMI LCD (H) User Manual preview
13.3 inch HDMI LCD (H)
Brand: Waveshare Pages: 12
Waeco Mobitronic RV-RMM-56 Installation And Operating Instructions Manual preview
Mobitronic RV-RMM-56
Brand: Waeco Pages: 87
Reer BeeConnect Plus 50120 Instruction Manual preview
BeeConnect Plus 50120
Brand: Reer Pages: 64
H&H Babyruf MBF 3838 Operating Instructions Manual preview
Babyruf MBF 3838
Brand: H&H Pages: 6
S&S Northern Merlin PM2+ User Manual preview
Merlin PM2+
Brand: S&S Northern Pages: 8
I-Tech iAP-2000 User Manual preview
iAP-2000
Brand: I-Tech Pages: 31
Dantherm MASTER SM 4.0 User And Maintenance Book preview
MASTER SM 4.0
Brand: Dantherm Pages: 84
NCR 7610-K453 Kit Instructions preview
7610-K453
Brand: NCR Pages: 6
Postium OBM-U090 User Manual preview
OBM-U090
Brand: Postium Pages: 44
Planar PS7050 User Manual preview
PS7050
Brand: Planar Pages: 42
ViewSonic ViewPanel VG175 Service Manual preview
ViewPanel VG175
Brand: ViewSonic Pages: 68
Samsung SyncMaster 320P Owner'S Manual preview
SyncMaster 320P
Brand: Samsung Pages: 70
Samsung SyncMaster 320P User Manual preview
SyncMaster 320P
Brand: Samsung Pages: 69
Fujitsu A17-5 ECO Operating Manual preview
A17-5 ECO
Brand: Fujitsu Pages: 35
Fujitsu 280X1024@75Hz User Manual preview
280X1024@75Hz
Brand: Fujitsu Pages: 10
Fujitsu 17inch User Manual preview
17inch
Brand: Fujitsu Pages: 15

Brands by name

Popular brands

Load more brands