manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

The IBM Flex System p260 Compute Node is a one-bay compute node and is used in an IBM Flex System
Enterprise Chassis.

Notes:

v

Power, cooling, removable-media drives, external ports, and Advanced System Management (ASM) are
provided by the IBM Flex System Enterprise Chassis.

v

The operating system in the compute node must provide support for the Universal Serial Bus (USB) to
enable the compute node to recognize and communicate internally with the removable-media drives
and front-panel USB ports.

Core electronics:

64-bit 2 x POWER7

®

processors

IBM Flex System p260 Compute Node
1-bay:

v

Model 7895-22X 16-way SMP 1-bay:
2 socket, 4-core or 8-core at 3.2, 3.3,
or 3.5 GHz

v

Model 7895-23A 4-way SMP 1-bay:
2 socket, 2-core at 4.0 GHz

v

Model 7895-23X 16-way SMP 1-bay:
2 socket, 4-core at 4.0 GHz or
8-core at 3.6 or 4.1 GHz

v

16 DIMM DDR3 slots. Maximum
capacity is 512 GB. With hard disk
drives (HDDs) or solid-state drives
(SSDs) installed, supports 4 GB and
8 GB very low profile (VLP)
DIMMs. With SSDs installed or in
diskless configurations, also
supports 2 GB, 16 GB, and 32 GB
low profile (LP) DIMMs.

POWER7 IOC I/O hub x 2 for the
IBM Flex System p260 Compute
Node

On-board, integrated features:

v

Service processor: IPMI, serial over
LAN (SOL)

v

SAS controller

v

USB 2.0

Local storage:

v

Zero, one, or two SAS 2.5 in. 300
GB, 600 GB, or 900 GB HDDs

v

Zero, one, or two SATA 1.8 in. 177
GB SSDs with SAS-to-SATA
conversion

v

Hardware mirroring supported

Network and storage adapter card
I/O options:

For a mapping of location codes, see
“System-board connectors” on page
14.

v

1 Gb Ethernet 4-port or 10 Gb
Ethernet KR 4-port card or 8-port
10 Gb converged network adapter
card in the I/O expansion card
slots (P1-C18, P1-C19) of the IBM
Flex System p260 Compute Node

v

8 Gb 2-port, 16 Gb 2-port, and 16
Gb 4-port Fibre Channel cards in
I/O expansion card slot P1-C19 of
the IBM Flex System p260
Compute Node

v

2-port 4X InfiniBand QDR
network adapter form factor
expansion card in the P1-C19 slot
of the IBM Flex System p260
Compute Node

v

2-port 10 Gb RoCE card form
factor expansion card in the
P1-C19 slot of the IBM Flex
System p260 Compute Node

Integrated functions:

v

Two 1 Gb Ethernet ports for
communication with the
management module

v

Automatic compute node restart

v

SOL over the management
network

v

Single USB 2.0 on base system
board for communication with
removable-media drives

v

Optical media available by shared
chassis feature

Environment: 

These compute nodes

comply with ASHRAE class A3
specifications. For details, see the
Environment specifications at
http://publib.boulder.ibm.com/
infocenter/flexsys/information/topic/
com.ibm.acc.8721.doc/
features_and_specifications.html.

Size:

v

Height: 55 mm (2.2 in.)

v

Depth: 492 mm (19.4 in.)

v

Width: 215 mm (8.5 in.)

Systems management:

v

Supported by IBM Flex System
Enterprise Chassis management
module (CMM)

v

Front panel LEDs

v

Management console: IBM Flex
System Manager, Hardware
Management Console (HMC), or
Integrated Virtualization Manager
(IVM)
Note:

The compute node can be

managed by only one management
console at a time.

v

Energy scale thermal management
for power management, power
oversubscription (throttling), and
environmental sensing

v

Field core override to disable cores
and save on licensing costs

v

Concurrent code update by using
IBM Flex System Manager Update
Manager, Inventory Collection,
multiple VIOS, and PowerVM

®

Enterprise

6

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

NEC C SERIES User Manual preview
C SERIES
Brand: NEC Pages: 26
Xenarc 1029 User Manual preview
1029
Brand: Xenarc Pages: 16
A&D UA-851 Specification preview
UA-851
Brand: A&D Pages: 2
A&D UA-621 Specification preview
UA-621
Brand: A&D Pages: 2
4iiii Viiiiva Quick Start Manual preview
Viiiiva
Brand: 4iiii Pages: 2
Digimate L-1721 User Manual preview
L-1721
Brand: Digimate Pages: 93
ElectrIQ eiQ-43CVSUWD120FSH User Manual preview
eiQ-43CVSUWD120FSH
Brand: ElectrIQ Pages: 21
IFM SI5012 Operating Instructions Manual preview
SI5012
Brand: IFM Pages: 17
YURAKU YUR.VISION YV216WB1 Brochure preview
YUR.VISION YV216WB1
Brand: YURAKU Pages: 2
Zenith P50W38 Installation And Operating Manual preview
P50W38
Brand: Zenith Pages: 36
Westinghouse LCM-20v5 Brochure preview
LCM-20v5
Brand: Westinghouse Pages: 4
Uniden BW4151 Owner'S Manual preview
BW4151
Brand: Uniden Pages: 24
Sanitas SBM 50 Instructions For Use Manual preview
SBM 50
Brand: Sanitas Pages: 80
Lanaform LA090204 User Manual preview
LA090204
Brand: Lanaform Pages: 312
OSEE LMW-156H User Manual preview
LMW-156H
Brand: OSEE Pages: 35
V7 D19W12C Specifications preview
D19W12C
Brand: V7 Pages: 1
Daktronics COLORSMART BB-3102 Display Manual preview
COLORSMART BB-3102
Brand: Daktronics Pages: 108
Pyle view PLHR7SP Instruction Manual preview
PLHR7SP
Brand: Pyle view Pages: 20

Brands by name

Popular brands

Load more brands