5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-6485-A Rev.15 P. 1 / 8
INSTRUCTION MANUAL
MULTI POWER MONITOR
(4 digital displays)
MODEL
53U
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■
PACKAGE INCLUDES:
Multi power monitor
(Body + Mounting bracket × 2 + gasket)............................(1)
■
MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■
INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
For detailed explanations to operate and program the mod-
ule, please refer to Model 53U Operating Manual (EM-
6485-B).
The 53U is programmable either by using the front control
buttons or the PC Configurator Software. For detailed in-
formation on the PC configuration, refer to the PMCFG us-
ers manual.
Software and manuals are downloadable at M-System’s
web site: http://www.m-system.co.jp
■
INTENDED USE
This equipment is a digital panel meter which measures
simultaneously several variables of a heavy-current power
system: current, voltage, active, reactive and apparent pow-
er, active and reactive energy, power factor, frequency, etc.
■
SYMBOLS USED ON THE PRODUCT AND IN THIS MANUAL
This symbol on the product indicates that the operator
must refer to an explanation in the user’s manual in order
to avoid the risk of injury or death of personnel or damage
to the instrument.
This symbol indicates double insulation.
POINTS OF CAUTION
■
CAUTION
• If Equipment is not used in a manner not specified by
M-System, the protection provided by the equipment may
be impaired.
■
CONFORMITY WITH EU DIRECTIVES OR UL
• This equipment is suitable for Pollution Degree 2, Meas-
urement Category III (input, transient voltage 6000V)
and Installation Category II (auxiliary power, transient
voltage 2500V).
And insulation class of this unit is as following.
Input to Auxiliary power supply: Reinforced insulation (550V)
Output to Auxiliary power supply: Reinforced insulation (300V)
Output to Input: Basic insulation (550V)
Prior to installation, check that the insulation class of
this unit satisfies the system requirements.
• The equipment must be mounted inside a panel.
• Altitude up to 2000 meters.
• Insert a noise filter for the power source connected to the
unit. Cosel Noise Filter Model NAC-06-472 or equivalent
is recommended.
• The equipment must be installed such that appropriate
clearance and creepage distances are maintained to con-
form to CE/UL requirements. Failure to observe these
requirements may invalidate the CE/UL conformance.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
• For safety, be sure to install a circuit breaker switch as
part of the building installation that conforms to IEC
60947-2 near the 53U so as to be operated easily, and
clearly indicate that the device is used to de-energize the
53U. The circuit breaker must be provided on both side of
the line or must be “common trip” type.
■
AUXILIARY POWER SUPPLY RATING & OPERATIONAL
RANGE
• Locate the auxiliary power supply rating marked on the
product and confirm its operational range as indicated
below:
100 – 240V AC rating: 85 – 264V AC, 47 – 66 Hz, < 8 VA
110 – 240V DC rating: 99 – 264V DC, < 4 W (UL ap-
proval is not available)
• For UL approved model, power input terminals are
marked with L and N instead of U(+) and V(–).
■
GENERAL PRECAUTION
• Before you remove or mount the unit, turn off the power
supply and input signal for safety.
