IBM i 830 Repair Manual Download Page 175

Page: 175 / 1000

If the failing item is a type number, go to “Type, Model, and Part Number list”

on page 885 to determine the part number.

If the failing item is a symbolic FRU, go to “Symbolic FRUs” on page 495 to
determine the part number.

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

0AD2 to 0AD3

Communications adapter card test failed

FI00718

0B25

Communications adapter card test failed

FI00719
FI00718
FI00727

0BA0, 0BAB, 0BB0,
0BD0 to 0BD1

Communications adapter card test failed

FI00719
FI00718

0BEE

I/O card Licensed Internal Code ended abnormally

FI00719
FI00718

0C10

Communications adapter card test failed

FI00719
FI00718
FI00727

0C20

Communications adapter card test failed

FI00719
FI00718

0C30

Adapter card failed modem interface test

FI00719
FI00718

0C40, 0C43

Synchronous-data-link-control send-receive test failed

FI00719
FI00718

0C50, 0C53

Binary synchronous control send-receive test failed

FI00719
FI00718

0C60, 0C63

Asynchronous send-receive test failed

FI00719
FI00718

0C70, 0C80

Communications adapter card test failed

FI00719
FI00718

0C90

Communications adapter card X.21 test failed

FI00719
FI00718

0CA1, 0CC0

Communications adapter card test failed

FI00719
FI00718

5007

Diagnostic wrap test completed; no errors detected

5008

Diagnostic wrap test completed; error was detected

FI00719
DPAC
FI00718

FFFF

User suspected communications problem.

UNAUPPR

Workstation Adapter Console Failing Items

Notes:

To determine the failing items, go to “Failing Items” on page 479.

To determine the associated part numbers, go to “Type, Model, and Part
Number list” on page 885.

To determine the parts associated with symbolic FRUs, such as “ANYBUS”, or
“DEVTERM”, go to “Symbolic FRUs” on page 495.

Failing Item

Description

Document Description

DPAC

Communications two-port adapter cable

Problem Analysis; Symbolic FRU Isolation

6A59

Chapter 2. Unit Reference Codes

161

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands