IBM i 830 Repair Manual Download Page 207 | Manualshive

Page: 207 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

1407

Service processor Licensed Internal Code failed

The Licensed Internal Code could not allocate resources on the Service
processor.

AJDGP01
SVCPROC
AJDG301

1408

Service processor Licensed Internal Code failed

AJDGP01
AJDG301
SVCPROC

1409

Service processor Licensed Internal Code failed

The Service processor was not ready for an interrupt that occurred.

AJDGP01
SVCPROC

1A01

I/O processor resource not available

A deactivation failed to get a resource controlled by Licensed Internal
Code.

CDAWKLD
FI00130
AJDG301

1A02

Not valid condition in I/O Processor Licensed Internal Code

An error in an activation or deactivation occurred.

FI00130
FI00131
FI00132

1A03

I/O processor resource not available

A resource that is needed to perform a requested function is not available
in the Licensed Internal Code.

FI00130
AJDG301
CDAWKLD

1A04

Recovered from condition in Licensed Internal Code.

The Licensed Internal Code has recovered from a condition that was not
expected.

FI00130
AJDG301
FI00131
FI00132

1A05 to 1A06

I/O processor card or Licensed Internal Code error

A microprocessor exception occurred on the I/O processor.

FI00130
FI00131
FI00132

1A07

I/O processor resource not available

The Licensed Internal Code could not allocate memory resources on the
I/O processor card.

CDAWKLD
FI00132
FI00130
AJDG301

1A08

Not valid condition in I/O Processor Licensed Internal Code

The Licensed Internal Code found a condition that should not have
occurred.

FI00130
FI00131
FI00132

1A09

Threshold overflow

The I/O processor card has detected a threshold of recoverable error
conditions. The errors are either wrong interruptions or memory error
corrections. If in communications, the line is still running.

Note:

If a large number of these errors occur during a short time, they may

be caused by an electrically noisy environment, a defective communications
I/O processor card or modem, or a communications I/O processor code
problem.

FI00131
FI00132
FI01117
FI00130

1A10

Error reported to system

The I/O processor error log is being filled faster than the errors are being
reported to the system. Check other errors reported to the system and
correct them.

B006

Chapter 2. Unit Reference Codes

193

«
...
205
206
207
208
209
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

eServer BladeCenter HS40 Type 8839

Brand: IBM Pages: 120

Brand: Stratus Pages: 106

Brand: IBM Pages: 75

AlphaServer ES47

Brand: HP Pages: 76

AlphaServer GS80

Brand: HP Pages: 88

Brand: HP Pages: 39

16/18-Port Cable Management Kit

Brand: HP Pages: 14

Brand: HP Pages: 49

AlphaServer ES47

Brand: HP Pages: 152

AlphaStation DS20

Brand: HP Pages: 15

AlphaServer ES45

Brand: HP Pages: 38

AB500A - Integrated Lights-Out Advanced

Brand: HP Pages: 43

AlphaServer GS1280 Systems

Brand: HP Pages: 59

2533t - Compaq Mobile Thin Client

Brand: HP Pages: 116

Brand: HP Pages: 206

127695-B21 - Smart Array 431 RAID Controller

Brand: HP Pages: 9

A3724A - SureStore E Hub S10

Brand: HP Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands