IBM i 830 Repair Manual Download Page 189 | Manualshive

Page: 189 / 1000

background image

Reference
Code

Description/Action Perform all actions before exchanging
Failing Items

Failing Item

9200

I/O processor addressed the tape unit; no response

Before exchanging any parts, do the following:

1.

Ensure that the device is powered on.

2.

Ensure that the SCSI cable between the device and the
I/O Processor or I/O Adaptor is seated correctly, and
that there are not bent or damaged pins on the SCSI
cable.

3.

Ensure that the terminating plug is attached to the
device.

86G9251
86G9274
86G9254
FI00131
EXTSCSI
17G1934
87G1531
86G9255

9201

Tape unit command timeout

Before exchanging any parts, do the following:

1.

Ensure that the device is powered on.

2.

Ensure that the SCSI cable between the device and the
I/O Processor or I/O Adaptor is seated correctly, and
that there are not bent or damaged pins on the SCSI
cable.

3.

Ensure that the terminating plug is attached to the
device.

86G9251
FI00131
86G9254
EXTSCSI
17G1934
86G9255
86G9274
FI00130

9202

Tape unit failed after Licensed Internal Code was loaded

Before exchanging any parts, do the following:

1.

Ensure that the device is powered on.

2.

Ensure that the SCSI cable between the device and the
I/O Processor or I/O Adaptor is seated correctly, and
that there are not bent or damaged pins on the SCSI
cable.

3.

Ensure that the terminating plug is attached to the
device.

86G9251
86G9274
86G9254

9210

Illegal or unsupported tape unit response

86G9251
FI00130
FI00131

9300

Tape unit failure

The tape drive reported a hardware error to the IOP; the
amber light on the tape drive may be blinking.

Perform “TU-PIP2” on page 448.

86G9251
LIBDEV
MLYTMED
86G9274
86G9255

9301

Tape device failure, redundancy lost

The tape device detected a hardware failure that does not
prevent the tape unit from completed the current
operation.

Refer to the Tape unit service information to determine the
failing item.

86G9251
LIBDEV
MLYTMED
86G9274
86G9255

9427

Chapter 2. Unit Reference Codes

175

«
...
187
188
189
190
191
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

Brand: Ganz Pages: 5

Brand: IBM Pages: 106

Brand: Vidyo Pages: 186

Brand: Advantech Pages: 43

SUPERSERVER 1015B-3

Brand: Supermicro Pages: 98

Brand: Fujitsu Pages: 26

Brand: Fujitsu Pages: 56

Brand: Fujitsu Pages: 36

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 30

ETERNUS DX Disk

Brand: Fujitsu Pages: 85

Brand: Fujitsu Pages: 111

BX630 - PRIMERGY - S2 Dual

Brand: Fujitsu Pages: 64

Brand: Fujitsu Pages: 68

CELVIN NAS QE707

Brand: Fujitsu Pages: 95

BX630 - PRIMERGY - S2 Dual

Brand: Fujitsu Pages: 90

D3320 PRIMERGY BX2560 M2

Brand: Fujitsu Pages: 80

Brand: Fujitsu Pages: 238

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands