IBM i 830 Repair Manual Download Page 206 | Manualshive

Page: 206 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

1308

Not valid condition in I/O Processor Licensed Internal Code

The Licensed Internal Code found a condition that should not have
occurred.

AJDGP01
AJDG301
FI00131

1309

I/O processor was not ready for interrupt that occurred

AJDGP01
FI00131
FI00132
FI01117

1310

I/O processor resource not available

The I/O processor error log is being filled faster than the errors are being
reported to the system. Check other errors reported to the system and
correct them.

1311

System bus error

FI00131
ANYBUS
AJDGP01
AJDG301

1312

A permanent I/O processor failure occurred

FI00131
AJDGP01

1313

System bus error

AJDG301
AJDGP01
FI00131

1316

I/O processor card or Licensed Internal Code error

AJDGP01
FI00132
FI00131

1317

I/O processor card error

Display the Service Action Log entry for this SRC. If the Failing Item
indicates IOP, then replace the IOP. If the Failing Item indicates SVCDOCS,
then do NOT replace the IOP. This is a recoverable error. Perform the
following:

1. If the I/O Processor is not operable and disk units are attached, use
Hardware Service Manager to re-IPL the IOP. Other resources attached to
the IOP may then need to be Varied On.

2. If disk units are not attached, perform the VRYCFG RESET(*YES)
command to reset the IOP and Vary On attached resources.

SVCDOCS

1318

I/O processor card error

FI00131

1403

Service processor Licensed Internal Code error

A resource needed to perform a requested function is not available in the
Licensed Internal Code.

AJDGP01
SVCPROC

1404

Service processor Licensed Internal Code error

The Licensed Internal Code has recovered from an unexpected condition.

AJDGP01
SVCPROC

1405

Service processor Licensed Internal Code error

A recoverable microcode condition occurred on the Service processor.

AJDGP01
SVCPROC

1406

Service processor Licensed Internal Code failed

A microprocessor exception occurred on the Service processor.

AJDGP01
SVCPROC
AJDG301

B006

192

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

«
...
204
205
206
207
208
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

Univerge SV8100

Brand: NEC Pages: 2

8841 - eServer xSeries 236

Brand: IBM Pages: 100

Brand: NAIM Pages: 16

Brand: Logicbus Pages: 8

Enterprise Server

Brand: Blackberry Pages: 88

Brand: Axel Pages: 28

BladeCenter HS20 Type 8843

Brand: IBM Pages: 112

WLNG-AN-DP500 Series

Brand: Quatech Pages: 120

Brand: AIC Pages: 64

Brand: Crestron Pages: 2

ProLiant ML350 G3

Brand: HP Pages: 44

ProLiant ML310e Gen8 v2

Brand: HP Pages: 43

ProLiant ML330 Generation 3

Brand: HP Pages: 34

PROLIANT ML350 G6

Brand: HP Pages: 145

ProLiant ML350 Gen9

Brand: HP Pages: 171

PROLIANT ML350 G6

Brand: HP Pages: 103

PROLIANT ML330 G6

Brand: HP Pages: 137

Brand: MSI Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands