IBM i 830 Repair Manual Download Page 317 | Manualshive

Page: 317 / 1000

background image

Attention:

You must fully connect the cable and tighten the connector’s

screws within

30 seconds

of when the cable makes contact with the port.

Otherwise, the link will fail and you must disconnect and reconnect the
cable again. If the connector screws are not tightened, errors will occur on
the link and it will fail.

b.

Disconnect the cable at the frame ID, card position, and port that you
recorded for the

″

second

″

failing resource, them wait 30 seconds and

reconnect it. See the 30 second attention notice in step 18a of this
procedure.

c.

Refresh the port status by:

1)

Wait 1 minute.

2)

Select the

Cancel

function.

3)

Select the

Refresh

function.

Determine if the link has become

″

operational

″

by repeating steps 1 through

15 of this procedure for a

second

time.

You

may

see a 6982 indicating that the loop went open and then a 6985

indicating that the loop recovered.

Note:

Return to the procedure that sent you here, when you are directed
to do so in steps 1 through 15 of this procedure.

This ends the procedure.

BUS PIP HSL-04

BUS PIP HSL-04, Use HSM to examine the HSL Loop to find a

failing I/O Bridge

resource.

1.

Sign on to SST or DST.

2.

Select

″

Start a service tool

″

.

3.

Select

″

Hardware service manager

″

.

4.

Select

″

Logical hardware resources

″

.

5.

Select

″

High-speed link (HSL) resources

″

.

6.

Move the cursor to the HSL loop that you are here to examine. Select the

″

Display detail

″

option.

7.

Select the function

″

Include non-reporting resources

″

.

8.

The display that appears is showing the port status of the Network Interface
Controller (NIC) for the loop that you selected. Record the resource name,
type-model, and serial number, if it has not been previously recorded.

9.

Is the status of the

″

Leading port to next resource

″ ″

operational

″

?

Yes

No

↓

You have found the first

″

failing

″

link. You will be directed to find the

″

failing HSL I/O Bridge

″

. Go to step 14 on page 304 of this procedure.

10.

Select function

″

Follow Leading Port

″

.

11.

Record the HSL resource name, type-model, part number, and port.

12.

Is the resource name the same name that you recorded for the NIC in step 8
of this procedure?

No

Yes

↓

You have followed the HSL links around the loop and back to the NIC
on the system. You did not find a failed link. Return to the procedure
that sent you here.

Bus, High-Speed Link (HSL) PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

303

«
...
315
316
317
318
319
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Xerox Pages: 220

Brand: Xerox Pages: 28

DocuPrint 100MX

Brand: Xerox Pages: 2

Flex System p270 Compute Node

Brand: IBM Pages: 510

Brand: Sun Oracle Pages: 222

System x3500 M2 Type 7839

Brand: IBM Pages: 126

MediaGrid ContentServer 3000

Brand: Omneon Pages: 2

Crestron 908012

Brand: SIERRA VIDEO SYSTEMS Pages: 32

TS-U100 - NAS Server - USB

Brand: TRENDnet Pages: 47

A+ AS -2114GT-DNR

Brand: Supermicro Pages: 126

Brand: Docomo Pages: 61

Brand: Fujitsu Pages: 26

Brand: Fujitsu Pages: 56

Brand: Fujitsu Pages: 36

Brand: Fujitsu Pages: 61

Brand: Fujitsu Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands