IBM i 830 Repair Manual Download Page 598

Page: 598 / 1000

Table 31.

System Model

Name of FRU
to Exchange

FRU Position

Link to Locations
Diagram

Link to Failing
Component Service
Information. (CCIN,
PN, Removal and
Installation
Procedure)

Models 830
and SB2

Network
Interface
Controller

M06

“Locations —
Models 830, SB2
System Unit with
FC 9074 Base I/O
Tower” on
page 709.

Table 41 on
page 710.

Models 840
and SB3

Network
Interface
Controller

M17

“Locations —
Models 840, SB3
System Unit with
Processor Tower
and FC 9079 Base
I/O Tower” on
page 719.

Table 42 on
page 720.

This ends the procedure:

SICNTRL

SICNTRL: high-speed link (HSL) Controller.

The failing component is the network interface controller (NIC) card in the system
unit.

Use the system model and the table below to determine the service information for
the failing component.

Table 32.

System Model

Name of FRU
to Exchange

FRU Position

Link to Locations
Diagram

Link to Failing
Component Service
Information. (CCIN,
PN, Removal and
Installation
Procedure)

Models 830
and SB2

Network
Interface
Controller

M06

“Locations —
Models 830, SB2
System Unit with
FC 9074 Base I/O
Tower” on
page 709.

Table 41 on
page 710.

Models 840
and SB3

Network
Interface
Controller

M17

“Locations —
Models 840, SB3
System Unit with
Processor Tower
and FC 9079 Base
I/O Tower” on
page 719.

Table 42 on
page 720.

This ends the procedure:

Symbolic FRUs

584

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands