IBM i 830 Repair Manual Download Page 151

Page: 151 / 1000

Reference
Code

Description/Action Perform all actions before exchanging
Failing Items

Failing Item

9100

Interface error detected by I/O processor or by tape unit

Before exchanging any parts, do the following:

Ensure that an interposer is connected between the I/O
processor and the SCSI cable.

Ensure that the SCSI cable between the interposer and
the device is seated correctly, and that there are no
bent or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the
device end of the SCSI cable.

FI00851
FI00856
05H3834
EXTSCSI
61G8324

9200

I/O processor addressed the tape unit; no response

Before exchanging any parts, do the following:

Ensure that the device is powered on.

Ensure that an interposer is connected between the I/O
processor and the SCSI cable.

Ensure that the SCSI cable between the interposer and
the device is seated correctly, and that there are no
bent or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the
device end of the SCSI cable.

FI00851
FI00856
05H3834
EXTSCSI
61G8324

9201

Tape unit command timeout

Before exchanging any parts, do the following:

Ensure that the device is powered on.

Ensure that an interposer is connected between the I/O
processor and the SCSI cable.

Ensure that the SCSI cable between the interposer and
the device is seated correctly, and that there are no
bent or damaged pins on the SCSI cable.

Ensure that a terminating plug is attached to the
device end of the SCSI cable.

FI00851
FI00856
05H3834
EXTSCSI
61G8324

9210

Illegal or unsupported tape unit response

FI00851
FI00856
FI00130

9300

Tape unit failure

DHK0002

9301

Tape device failure, redundancy lost

The tape unit detected a hardware failure that does not
prevent the tape unit from completing the present
operation.

See the 3490 Tape Unit service information to determine
the failing item.

DHK0002

9302

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O
processor data. For more information, see the

iSeries Service

Functions

information or ask your next level of support for

assistance.

FI00130

9310

Licensed Internal Code for the tape unit is not correct

FI00851
FI00130

3490

Chapter 2. Unit Reference Codes

137

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands