IBM i 830 Repair Manual Download Page 262

Page: 262 / 1000

Reference
Code

Description/Action Perform all actions before exchanging
Failing Items

Failing Item

Location

5001

DST received no response from a work station controller

The workstation I/O processor for the system or partition
console did not respond.

If the system uses an

iSeries

Operations Console, perform

“Operations Console-PIP1” on page 381.

Otherwise, perform “BUS PIP CNSL01” on page 287.

FI00380
AJDG301

5002

DST problem attempting to use the system console

A code problem occurred during an attempt to use the system
console.

Perform “LIC-PIP3” on page 344.

AJDG301
FI00380

5003

Service program failed

The ASCII system console failed to respond.

FI00320
FI00602
UG3USR1
AJDG301
FI00380

5004

DST console failed to respond

The system console failed to respond.

If the system uses an

iSeries

Operations Console, perform

“Operations Console-PIP1” on page 381.

Otherwise, perform “TWSC-PIP1” on page 465.

FI00320
FI00602
UG3USR1
AJDG301
FI00380

5005

Service program failed

The workstation adapter system console failed to respond.

Perform “WSAC-PIP1” on page 477.

FI00320
FI00602
UG3USR1
AJDG301
FI00380

5007

Service program failed

The workstation adapter console failed to respond.

If the system uses an

iSeries

Operations Console, perform

“Operations Console-PIP1” on page 381.

Otherwise, perform “WSAC-PIP1” on page 477.

FI00320
FI00602
UG3USR1
AJDG301
FI00380

5008

DST console failed to respond

Perform Operations Console-PIP3.

FI00719

5010

IPL service function ended abnormally

Perform “LIC-PIP4” on page 345.

AJDG301

5082

DST lost contact with the console

A service program lost contact with the system console.

Do you have a twinaxial terminal for the console?

Yes

↓

Perform “TWSC-PIP1” on page 465.

Perform “WSAC-PIP1” on page 477.

AJDG301
UG3USR1

B6xx (including A6xx)

248

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands