IBM i 830 Repair Manual Download Page 405 | Manualshive

Page: 405 / 1000

background image

b.

Power on the system or frame that you are working on. (Frames with FC
5078/0578 attached – reconnect the lower frame power supply AC jumper
cables at the AC input/battery charger, or at the AC modules on dual line
cord frames.)

Does a power reference code occur?

Yes

No

↓

Replace the DASD backplane that the power cable was removed from
in this step, see symbolic FRU “DEVBPLN” on page 525.

10.

Is a second lower DASD backplane installed?

No

Yes

↓

Go to step 9 on page 390 of this procedure.

11.

Replace the following one at a time:

v

DASD backplane upper (CCIN 283C) see symbolic FRU “DEVBPLN” on
page 525.

v

System backplane, see symbolic FRU “SYSBKPL” on page 598.

This ends the procedure.

12.

Perform the following:

a.

Power off the frame that you are working on. (Frames with FC 5078/0578
attached – trace and remove the lower frame power supply AC jumper
cables at the AC input/battery charger, or at the AC modules on dual line
cord frames.)

b.

Reinstall all of the cards that you removed in step 1 on page 389 of this
procedure.

c.

Reconnect the AC power cable to the unit that you are working on.

d.

Power on the system or frame that you are working on. (Frames with FC
5078/0578 attached – reconnect the lower frame power supply AC jumper
cables at the AC input/battery charger, or at the AC modules on dual line
cord frames.)

13.

Does a power reference code occur?

Yes

No

↓

Go to step 16 on page 392 of this procedure.

14.

Perform the following:

a.

Power off the frame that you are working on. (Frames with FC 5078/0578
attached – trace and remove the lower frame power supply AC jumper
cables at the AC input/battery charger, or at the AC modules on dual line
cord frames.)

b.

Disconnect one of the cards that you connected in step 12 of this
procedure.

c.

Power on the system or frame that you are working on. (Frames with FC
5078/0578 attached – reconnect the lower frame power supply AC jumper
cables at the AC input/battery charger, or the AC modules on dual line
cord frames.)

Does a power reference code occur?

Yes

No

Power PIPs

Chapter 3. Problem Isolation Procedures (PIPs), Failing Items, and Symbolic FRU Isolation

391

«
...
403
404
405
406
407
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

x3655 - System - 7985

Brand: IBM Pages: 118

Brand: Sun Fire Pages: 66

SUPERO SuperServer 6026TT-GIBQRF

Brand: Supero Pages: 104

Brand: Hi-flying Pages: 29

Brand: Kontron Pages: 110

Silex Pricom SX-2000U2

Brand: Silex technology Pages: 1

Brand: IBM Pages: 36

Brand: Cabletron Systems Pages: 100

Brand: Inspur Pages: 2

PRIMERGY BX620 S5

Brand: Fujitsu Pages: 50

PRIMERGY BX620 S4

Brand: Fujitsu Pages: 81

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 46

PRIMERGY BX620 S6

Brand: Fujitsu Pages: 56

Primergy BX920 S4

Brand: Fujitsu Pages: 66

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 70

PRIMERGY BX920 S2

Brand: Fujitsu Pages: 102

PRIMERGY BX400 S1

Brand: Fujitsu Pages: 60

PRIMERGY BX900 S1

Brand: Fujitsu Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands