IBM i 830 Repair Manual Download Page 205 | Manualshive

Page: 205 / 1000

background image

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

1205 to 1206

I/O processor card or Licensed Internal Code error

A microprocessor exception occurred on the I/O processor.

AJEQU00
FI00131
FI00132

1207

I/O processor resource not available

The Licensed Internal Code could not allocate memory resources on the
I/O processor card.

AJEQU00
AJDG301

1208

Not valid condition in I/O Processor Licensed Internal Code

The Licensed Internal Code found a condition that should not have
occurred.

AJEQU00
AJDG301
FI00131

1209

I/O processor was not ready for interrupt that occurred

AJEQU00
FI00131

1210

I/O processor resource not available

The I/O processor error log is being filled faster than the errors are being
reported to the system. Check other errors reported to the system and
correct them.

1211

System bus error

FI00131
ANYBUS
AJEQU00
AJDG301

1212

A permanent I/O processor failure occurred

FI00131
AJEQU00

1213

System bus error

AJDG301
AJEQU00
FI00131

1214 to 1215

I/O processor card or Licensed Internal Code error

FI00131
AJEQU00

1301

I/O processor resource not available

An activation or deactivation failed to get a resource controlled by Licensed
Internal Code.

CDAWKLD
AJDGP01
AJDG301

1302

Not valid condition in I/O Processor Licensed Internal Code

An error in an activation or deactivation occurred.

AJDGP01
AJDG301
FI00131
FI00132

1303

I/O processor resource not available

A resource needed to perform a requested function is not available in the
Licensed Internal Code.

IOACNFG
AJDGP01
AJDG301

1304

Not valid condition in I/O Processor Licensed Internal Code

The Licensed Internal Code has recovered from an unexpected condition.

AJDGP01
AJDG301
FI00131
FI00132

1305 to 1306

I/O processor card or Licensed Internal Code error

A microprocessor exception occurred on the I/O processor.

AJDGP01
FI00131
FI00132
BACKPLN

1307

I/O processor resource not available

The Licensed Internal Code could not allocate memory resources on the
I/O processor card.

AJDGP01
AJDG301
IOACNFG
FI00132

B006

Chapter 2. Unit Reference Codes

191

«
...
203
204
205
206
207
...
»

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

8835 - Eserver 325 - 1 GB RAM

Brand: IBM Pages: 68

Brand: IBM Pages: 42

Brand: GarrettCom Pages: 55

Brand: IBM Pages: 491

System x3650 M4 BD Type 5466

Brand: IBM Pages: 786

Brand: AXIOMTEK Pages: 76

SMAVIA DMS 2400 II

Brand: dallmeier Pages: 36

ProLiant MicroServer

Brand: HP Pages: 22

ProLiant MicroServer Gen8

Brand: HP Pages: 104

ProLiant DL560 Generation9

Brand: HP Pages: 57

ProLiant MicroServer Generation 8

Brand: HP Pages: 36

ProLiant DL585 G7

Brand: HP Pages: 126

ProLiant ML310e Gen

Brand: HP Pages: 92

Brand: HP Pages: 40

ProLiant DL580 G7

Brand: HP Pages: 130

ProLiant DL580 Gen9

Brand: HP Pages: 108

ProLiant Lights-Out 100i

Brand: HP Pages: 11

ProLiant DL560 Gen8

Brand: HP Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands