IBM i 830 Repair Manual Download Page 140

Page: 140 / 1000

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

3102

I/O processor card detected interface error

Error occurred on SCSI bus 2.

Perform “SDIOP-PIP13” on page 404.

STORIOA
FI01107
FI01140
BACKPLN

3109

I/O processor timed out a device command

Perform “SDIOP-PIP16” on page 407.

FI01105
STORIOA
FI01140
BACKPLN
FI01106

3110

I/O processor card detected interface error

Perform “SDIOP-PIP16” on page 407.

FI01105
STORIOA
FI01140
BACKPLN
FI01106

3136

The removable media device is assigned elsewhere

USER
FI01105

3200

A tape/CD or disk device reported a failure

FI01105
STORIOA
IOP
MEDIA

3203

Disk media format bad

FI01105

3205, 3215

Disk sector read error

Disk unit data may need to be reloaded, but the disk unit does not need to
be replaced.

FI01105

3250

Disk unit requires initialization before use.

Perform a D-IPL and work on errors found in the log.

USER

3300

Storage unit detected a media problem

Perform “SDIOP-PIP1” on page 401.

MEDIA
FI00121
FI01141

3400

I/O processor card detected device error

NOTE: If external devices are attached check EXTSCSI and DEVTERM first.

FI02112
STORIOA
FI01106
DEVTERM
FI01140

3401

Device backplane problem

DEVBPLN

3501

I/O processor Licensed Internal Code error

AJDGP01
IOP

3600 to 3601

System log entry only, no service action required

6070

A permanent I/O processor failure occurred

IOP

6071

I/O processor Licensed Internal Code error

AJDGP01

6072

I/O processor Licensed Internal Code error

AJDGP01
IOP

6073

IPL device not ready

MEDIA
FI01105
USER

6075

I/O processor resource not available

AJDGP01

2749, 2767, 2768, 2842, 2843, 284B

126

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands