IBM i 830 Repair Manual Download Page 142

Page: 142 / 1000

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

8141

IOA detected recoverable device error

No action is required. This reference code is logged for information only.

8145

A recoverable I/O processor error occurred.

STORIOA

8146

Disk device detected recoverable error

FI01105

8150

A permanent I/O processor failure occurred

STORIOA
IOP
FI01107
ANYBUS

8151

I/O processor Licensed Internal Code error

AJDGP01
STORIOA

8155 to 8156

A permanent I/O processor failure occurred

AJDGP01
STORIOA

8200

I/O processor Licensed Internal Code error

AJDGP01
IOP

8300

I/O processor card or Licensed Internal Code error

A microprocessor exception occurred on the I/O processor.

STORIOA
IOP
AJDGP01

8301

Not valid condition in I/O Processor Licensed Internal Code

The Licensed Internal Code found a condition that should not have
occurred.

FI01101
AJDGP01
IOP

8400

I/O processor Licensed Internal Code error

AJDGP01

9000 to 9001

I/O processor card detected device error

FI01105
STORIOA

9002

I/O processor card detected device error

Perform “SDIOP-PIP16” on page 407.

FI01105
STORIOA
FI01140
BACKPLN
FI01106

9008

I/O card does not support functions expected by devices

Perform “SDIOP-PIP25” on page 425.

SVCDOCS

9010

Cache data associated with attached devices cannot be found

Perform “SDIOP-PIP19” on page 415.

SVCDOCS

9011

Cache data belongs to devices other than those attached

Perform “SDIOP-PIP19” on page 415.

SVCDOCS

9012

IOP requires a cache adaptor card but cannot find it.

The cache adapter card is missing or broken.

Perform “SDIOP-PIP29” on page 432.

CACHE

9013

The IOP and attached cache adaptor card are not compatible.

Perform “SDIOP-PIP19” on page 415.

SVCDOCS

9020 to 9021

Array not functional due to present hardware configuration.

Perform “SDIOP-PIP20” on page 417.

SVCDOCS

2749, 2767, 2768, 2842, 2843, 284B

128

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands