manualshive.com logo in svg

IBM i 830, Repair Manual

Get your hands on the IBM i 830 Repair Manual today and troubleshoot your device with ease. This comprehensive manual is available for free download from manualshive.com. With step-by-step instructions and detailed diagrams, you can fix your IBM i 830 in no time.

Share
Download
background image

Contents

Safety and Environmental Notices . . . ix

Danger Notices .

.

.

.

.

.

.

.

.

.

.

.

. ix

Caution Notices .

.

.

.

.

.

.

.

.

.

.

.

. x

Attention Notices

.

.

.

.

.

.

.

.

.

.

.

. xi

Laser Safety Information .

.

.

.

.

.

.

.

.

. xi

Product Recycling and Disposal.

.

.

.

.

.

.

. xi

Battery Return Program .

.

.

.

.

.

.

.

.

. xi

Environmental Design .

.

.

.

.

.

.

.

.

.

. xi

Part 1. Problem Analysis . . . . . . 1

Chapter 1. Starting Problem Analysis . . 3

Starting Problem Analysis .

.

.

.

.

.

.

.

.

. 3

System Service Library Structure.

.

.

.

.

.

. 3

Starting Point for All Problems .

.

.

.

.

.

. 4

Using the Service Action Log .

.

.

.

.

.

.

.

. 9

Using the Product Activity Log .

.

.

.

.

.

.

. 11

Using the Problem Log

.

.

.

.

.

.

.

.

.

. 12

Handling Problems for Non-critical Resources .

.

. 13

Analyzing Intermittent Problems .

.

.

.

.

.

. 14

Safety .

.

.

.

.

.

.

.

.

.

.

.

.

.

. 14

Special Tools and Equipment

.

.

.

.

.

.

. 14

How to Use This Intermittent Problem Section

. 15

Correcting Intermittent Problems .

.

.

.

.

. 15

General Intermittent Problem Checklist .

.

.

. 16

How to Analyze the Intermittent Problem .

.

. 20

Intermittent Symptom Table .

.

.

.

.

.

.

. 20

Failing Area INT-PIP Table .

.

.

.

.

.

.

. 21

Analyzing IPL Problems .

.

.

.

.

.

.

.

.

. 22

Start Analyzing IPL Problems Here

.

.

.

.

. 22

Cannot Perform IPL from the Control Panel (No
SRC).

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 22

Cannot Perform IPL at a Specified Time (No
SRC).

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 23

Cannot Perform IPL from a Remote Location (No
SRC).

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 27

Cannot Automatically Perform an IPL after a
Power Failure

.

.

.

.

.

.

.

.

.

.

.

. 36

Analyzing Power Problems .

.

.

.

.

.

.

.

. 37

Start Analyzing Power Problems Here

.

.

.

. 37

Cannot Power On System Unit (No SRC) .

.

. 38

Cannot Power On Secondary Frame or Unit (No
SRC).

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 42

System or Expansion Unit Cannot Become
Powered Off .

.

.

.

.

.

.

.

.

.

.

.

. 56

Chapter 2. Unit Reference Codes . . . 59

How to Use This Section .

.

.

.

.

.

.

.

.

. 59

SRC Exception Table .

.

.

.

.

.

.

.

.

.

. 61

(0000) Control Panel Reference Codes.

.

.

.

.

. 62

Control Panel Failing Items .

.

.

.

.

.

.

. 64

(1xxx) System Power Control Network (SPCN)
Reference Codes .

.

.

.

.

.

.

.

.

.

.

.

. 64

System Power Control Network Failing Items

116

(2105) Disk Unit Reference Codes.

.

.

.

.

.

. 117

Disk Unit Failing Items .

.

.

.

.

.

.

.

. 118

(2746) Twinaxial –Workstation Adapter Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 118

Workstation Adapter Failing Items .

.

.

.

. 119

(2748, 2763, 2778) Reference Codes .

.

.

.

.

. 119

Failing Items

.

.

.

.

.

.

.

.

.

.

.

. 123

(2749, 2767, 2768, 2842, 2843, 284B) Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 124

Failing Items

.

.

.

.

.

.

.

.

.

.

.

. 130

(2765, 2766) Reference Codes .

.

.

.

.

.

.

. 131

Failing Items

.

.

.

.

.

.

.

.

.

.

.

. 133

(283C, 283D, 283F) Device Backplane Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 133

Failing Items

.

.

.

.

.

.

.

.

.

.

.

. 134

(3490) Tape Unit Reference Codes

.

.

.

.

.

. 134

Tape Unit Failing Items .

.

.

.

.

.

.

.

. 140

(3494) Tape Library Reference Codes

.

.

.

.

. 140

Tape Library Failing Items .

.

.

.

.

.

.

. 142

(3570) Tape Unit Reference Codes

.

.

.

.

.

. 142

Tape Unit Failing Items .

.

.

.

.

.

.

.

. 146

(3590) Tape Unit Reference Codes

.

.

.

.

.

. 146

Tape Unit Failing Items .

.

.

.

.

.

.

.

. 150

(432x, 660x, 671x, 673x) Disk Unit Reference Codes 151

Disk Unit Failing Items .

.

.

.

.

.

.

.

. 153

(632x, 6330) Optical Storage Unit Reference Codes

154

Optical Storage Unit Failing Items

.

.

.

.

. 156

(63A0) Tape Unit Reference Codes .

.

.

.

.

. 156

Tape Unit Failing Items .

.

.

.

.

.

.

.

. 160

(6A59) Workstation Adapter Console Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 160

Workstation Adapter Console Failing Items .

. 161

(7208) Tape Drive Reference Codes .

.

.

.

.

. 162

(7208) Model 002 Tape Drive Reference Codes

.

. 162

Model 002 Tape Drive Failing Items .

.

.

.

.

. 166

(7208) Model 012 Tape Drive Reference Codes

.

. 166

Model 012 Tape Drive Failing Items .

.

.

.

. 172

(9348) Tape Unit Reference Codes

.

.

.

.

.

. 172

(9427) Tape Unit Reference Codes

.

.

.

.

.

. 173

Tape Unit Failing Items .

.

.

.

.

.

.

.

. 178

(A1xx, B1xx) Service Processor Reference Codes

179

Service Processor Failing Items

.

.

.

.

.

. 182

(A6xx) LIC Reference Codes

.

.

.

.

.

.

.

. 183

(A9xx, B9xx) Reference Codes .

.

.

.

.

.

.

. 183

(B003) Asynchronous Communications Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 183

Asynchronous Communications Failing Items

189

(B006) Common Licensed Internal Code Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 190

Common Licensed Internal Code Failing Items

194

(B070) Reference Codes .

.

.

.

.

.

.

.

.

. 194

Failing Items

.

.

.

.

.

.

.

.

.

.

.

. 202

(B075) Workstation Adapter Console Reference
Codes .

.

.

.

.

.

.

.

.

.

.

.

.

.

.

. 202

Workstation Adapter Console Failing Items .

. 206

(B2xx) Logical Partition Reference Codes .

.

.

. 207

© Copyright IBM Corp. 2000, 2001

iii

Summary of Contents for i 830









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for i 830

D-Link DP-300+ User Manual preview
DP-300+
Brand: D-Link Pages: 38
D-Link Epress EtherNetwork DP-301P+ Datasheet preview
Epress EtherNetwork DP-301P+
Brand: D-Link Pages: 2
H3C UniServer E3200 G3 User Manual preview
UniServer E3200 G3
Brand: H3C Pages: 401
IBM Flex System p270 Compute Node Installation And Service Manual preview
Flex System p270 Compute Node
Brand: IBM Pages: 510
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
Supermicro SuperServer E300-9C User Manual preview
SuperServer E300-9C
Brand: Supermicro Pages: 113
RaidSonic IB-NAS4210-B Brochure & Specs preview
IB-NAS4210-B
Brand: RaidSonic Pages: 2
Supermicro AS -5019D-FTN4 User Manual preview
AS -5019D-FTN4
Brand: Supermicro Pages: 113
xFusion Digital Technologies FusionServer XH321 V5 Manual preview
FusionServer XH321 V5
Brand: xFusion Digital Technologies Pages: 76
Digi Connectware PortServer TS 8/16 Configuration And Administration Manual preview
Connectware PortServer TS 8/16
Brand: Digi Pages: 106
HP StorageWorks E Series Getting Started preview
StorageWorks E Series
Brand: HP Pages: 8
HP StorageWorks 9000s NAS Quick Reference And Rack Installation Instructions preview
StorageWorks 9000s NAS
Brand: HP Pages: 7
HP StorageWorks NAS e7000 v2 Specifications preview
StorageWorks NAS e7000 v2
Brand: HP Pages: 2
HP StorageWorks NAS e7000 v2 Quick Start Manual preview
StorageWorks NAS e7000 v2
Brand: HP Pages: 70
HP StorageWorks 600 All-in-One Maintenance And Service Manual preview
StorageWorks 600 All-in-One
Brand: HP Pages: 58
HP StorageWorks All-in-One SB600c - Storage Blade User Manual preview
StorageWorks All-in-One SB600c - Storage Blade
Brand: HP Pages: 60
Sony XDAAI1PK Brochure preview
XDAAI1PK
Brand: Sony Pages: 8
Sony BSV-M1 - StorStation NAS Server Operating Instructions Manual preview
BSV-M1 - StorStation NAS Server
Brand: Sony Pages: 58

Brands by name

Popular brands

Load more brands