IBM i 830 Repair Manual Download Page 316

Page: 316 / 1000

Select the

Associated packaging resources

option for the HSL I/O adapter

with the resource name that you recorded.

Record the frame ID, card position, and port. Record this information for
the

″

first

″

failing link in “Appendix G. HSL Link Status Diagnosis Form” on

page 967.

Select the

Display detail

option and record the card position for the

″

first

″

failing resource.

15.

Find the information for the other

(second)

failing resource using the following

steps:

Record this information as the

″

second

″

failing resource on the link.

Select the

Cancel

function to return to the

″

Packaging resource associated with

a logical resource

″

display.

Select the

Cancel

function again, to return to the

″

Logical hardware associated

with HSL ring

″

display.

Select the

Display detail

option for the HSL I/O adapter with the name of

the

″

first

″

failing resource.

Select the

Follow leading port

″

function.

You have located the

″

second

″

failing resource on the link.

Record the resource name, card type-model, part number, port.

Select the

Cancel

function to return to the

″

Logical hardware associated HSL

rings

″

display.

Select the

Associated packaging resources

option for the HSL I/O adapter with

the resource name that you recorded for the

″

second

″

failed resource.

Record the frame ID, card position, and port. Record this information for
the

″

second

″

failing link in “Appendix G. HSL Link Status Diagnosis Form”

on page 967.

Select the

Display detail

option and record the card position for the

″

second

″

failing resource.

16.

Have you repeated steps 1 through 15 for a

second

time during this

procedure?

Yes

↓

Return to the procedure that sent you here.

This ends the procedure.

17.

Does the

″

first

″

failing resource and the

″

second

″

failing resource have the same

frame ID?

Yes

↓

Return to the procedure that sent you here.

This ends the procedure.

18.

The following steps guide you through disconnecting and reconnecting the
HSL cable connection between the

first

and

second

failing resources to

determine if the cable connectors are properly seated:

Disconnect the cable at the frame ID, card position, and port that you
recorded for the

″

first

″

failing resource, then wait 30 seconds and reconnect

it.

Bus, High-Speed Link (HSL) PIPs

302

iSeries Model 830, 840, SB2, and SB3 Problem Analysis, Repair and Parts V5R1

Summary of Contents for i 830








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands

IBM i 830, Repair Manual

Search results

Summary of Contents for i 830

Reviews:

Related manuals for i 830

Brands by name

Popular brands