Docomo N-09A, Instruction Manual

Page: 459 / 572

457 Continued on next page
Appendix
/Troubleshooting
“Connection interrupted”
●
i-mode connection was interrupted due to poor
reception. Move to a good signal location before using
i-mode services.
→ p.47
●
If this message appears in a good signal location with
the “
” mark, the site is extremely busy. Retry after a
while.
“Continue using i-
α
ppli and transmit data?”
●
This message appears when you selected “NO” or
“Terminate i-
α
ppli” on the message “Data transmission
is frequent Continue transmission?” Select “YES” to
continue i-
α
ppli communication. To exit i-
α
ppli, select
“Terminate i-
α
ppli”.
“Could not be found”
●
There is no response from the Bluetooth device, and it
cannot be registered or connected.
“Current UIM is not registered as IC owner Unable
to delete”
“Current UIM is not registered as IC owner Unable
to download”
“Current UIM is not registered as IC owner Unable
to move”
“Current UIM is not registered as IC owner Unable
to run”
“Current UIM is not registered as IC owner Unable
to upgrade”
●
This message appears when the inserted FOMA card
(UIM) is not registered in FeliCa then you attempt to
start Osaifu-Keitai i-
α
ppli or move the i-
α
ppli from a
microSD card.
D
“Data in B mode phonebook is unavailable”
●
“Phonebook 2in1 setting” is set to “B”, and PushTalk
cannot be made. Change the “Phonebook 2in1 setting”
to “A”, and retry.
→ p.406
“Data in IC card is full Unable to download Delete
service?”
“Data in IC card is full Unable to move Delete
service?”
“Data in IC card is full Unable to run Delete
service?”
“Data in IC card is full Unable to upgrade Delete
service?”
●
This message appears when you attempt to download
Osaifu-Keitai i-
α
ppli or move it from a microSD card but
space is insufficient in the IC card. Select “YES” to view
already-stored Osaifu-Keitai services, space (bytes)
allocated by deleting the service, and necessary area
size. Select a service, and follow the instructions to
start i-
α
ppli and delete the service.
“Data is too long A part is deleted”
●
The size of the address, subject, main text or multiple
data exceeds the maximum. The excess part will be
deleted, and the New mail screen appears.
“Data is too long Please delete message”
●
The size including quotation marks in the main text of
i-mode mail to quote to send a reply exceeds 5,000
double-byte characters. Delete text to reduce the size
to 5,000 double-byte characters or less.
“Data transmission is frequent Continue
transmission?”
●
This message appears when i-
α
ppli communication is
extremely frequent in a given time span. Select “YES”
to continue i-
α
ppli communication, or “NO” to quit
communication. To exit i-
α
ppli, select “Terminate
i-
α
ppli”.
“Data transmission is frequent Press CLR and
confirm data transmission”
●
This message appears when communication from the
i-
α
ppli standby screen is extremely frequent in a given
time span. Press
t
to select whether to allow
communication from the i-
α
ppli standby screen or
whether to close the i-
α
ppli standby screen.
→
p.278
“Dial/Receive calls activating Original lock”
●
This message when you attempt a prohibited operation
while Original lock is set on “Dial/sending mail”.
→
p.133
“Download failed”
●
This message appears when a communication error
occurs while downloading a melody, Chara-den
character or download dictionary, or when the
downloaded data is invalid.
E
“Editing now Unable to delete”
●
This message appears when you are editing mail
stored in Draft and attempt to delete the mail.
“Enter correct Network Security Code”
●
This message appears when you entered a wrong
network security code. Enter the correct network
security code.
→
p.124
“Error in image Does not work correctly”
●
This message appears when a Flash movie cannot be
played due to an error found in the data.
“Error Register forwarding number”
●
This message appears when you have subscribed to
the Call Forwarding service and attempt to forward an
incoming call by selecting “Call Forwarding” from the
function menu without setting the forwarding number.
→ p.399
“Exceeds max number of simultaneous calls”
●
This message appears when you select 5 or more
members then dial. Reduce the number of members to
4 or fewer then redial.