Docomo N-09A, Instruction Manual

Page: 461 / 572

459 Continued on next page
Appendix
/Troubleshooting
“Message too long to add header & signature”
●
This message appears when you attempt to forward
i-mode mail but the header/signature cannot be
automatically added as the size including header/
signature exceeds 5,000 double-byte characters.
“Message too long to add signature”
●
The total size of the main text and signature exceeds
5,000 double-byte characters, and the signature cannot
be added.
N
“No channel found”
●
No channel available in the area is found.
“No channel info”
●
There is no channel information, and you cannot
compose a suggested message.
“No data”
●
This message appears when no phonebook entry
matches the search phonebook condition.
“No microSD”
●
This message appears when a microSD card is not
properly inserted or may be damaged. Check if a
microSD card is properly inserted.
→
p.324
“No requested data Delete this desktop icon?”
●
This message appears when you select the desktop
icon or desktop info of deleted data.
“No requested software”
●
This message appears when you attempt to start
i-
α
ppli from mail, infrared data exchange, Bar code
reader, IC card or data broadcast, but it is not found.
“No response (408)”
●
There is no response from the site, and the connection
was interrupted. Retry connection.
“No response”
●
No Bluetooth device is found near the FOMA terminal.
“No response”
●
This message appears when user authentication using
the IC card authentication function failed due to
timeout.
→ p.135
“No response Continue?” (During infrared data
exchange/iC communication)
●
The other party cannot be found/detected. Place
infrared data ports facing each other during infrared
data exchange. Check the
e
marks and put them
close again during iC communication. Select “YES”
and press
d
to retry.
→
pp.339, 340
“No Switch”
●
This message appears when the other party is
establishing a packet communication (including
i-mode) and you cannot switch a voice call to a
videophone call. Check the other party’s status and
retry.
→ p.55
“Not correspond contents”
●
Information read with Bar code reader contains content
unsupported by the FOMA terminal and cannot be
recognized.
O
“Other function active Cannot operate”
“Other function active Cannot start”
●
This message appears when you attempt an operation
unavailable during call.
“Out of service area”
●
This message appears when you attempt to use
i-mode services out of service area or in a poor signal
location. Move until “
” appears, then use i-mode
services.
→
p.47
P
“Page is not found (404)”
●
The site is not found. It may not exist.
“Password is not correct (401)”
●
This message appears when authentication fails on the
“Authentication” or “Re-authentication” screen. Select
“YES” to authenticate again.
“Phone/UIM ID will be sent”
●
This message may appear while viewing i-mode sites
or Internet websites. Select “YES” to send mobile
phone serial number information. Select “NO” not to
send.
→ p.181
“PIN1 code blocked”
●
This message appears when the power is turned on
while PIN1 code is locked. Press
d
to open the Enter
PUK code screen. Enter the correct PUK code to
unlock the PIN1 code.
→
p.125
“Please wait”
●
The voice line/packet communication system is down,
or the voice line network/packet communication
network is extremely busy. Use voice calls/videophone/
i-mode after a while.
You can still make emergency calls (110, 119, 118).
You may not be connected depending on the situation.
“Please wait for a while (packet)”
●
The packet communication system is down,or the
packet communication network is extremely busy. Retry
after a while.
“PUK code blocked”
●
This message appears when you turn on the power or
attempt to perform FOMA card (UIM) operations while
PUK code is blocked. Contact a docomo Shop.
→
p.124