manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

The Dell Force10 MXL Blade is a cutting-edge network switch designed for high-performance data centers. Unlock its full potential by easily configuring its advanced features through our comprehensive and user-friendly manual, available for free download at manualshive.com. Empower your network infrastructure today with this unparalleled product.

Share
Download
background image

676

|

Debugging and Diagnostics

www.dell.com | support.dell.com

Defaults

none

Command Modes

EXEC Privilege

Command

History

offline stack-unit 

Place a stack unit in the offline state.

Syntax

offline

 

stack-unit

 

number

Parameters

Defaults

none

Command Mode

EXEC Privilege

Command

History

H

Usage

Information

The system reboots when the off-line diagnostics complete. This is an automatic process. A warning 
message appears when the 

offline stack-unit 

command is implemented. 

Warning - Diagnostic execution will cause stack-unit to reboot after 

completion of diags.

Proceed with Offline-Diags [confirm yes/no]:y

level0

Enter the keyword 

level0

 to run Level 0 diagnostics. Level 0 diagnostics check for the 

presence of various components and perform essential path verifications. In addition, they 
verify the identification registers of the components on the board.

level1

Enter the keyword 

Level1

 to run Level 1 diagnostics. Level 1 diagnostics is a smaller set of 

diagnostic tests with support for automatic partitioning. They perform status/self test for all 
the components on the board and test their registers for appropriate values. In addition, they 
perform extensive tests on memory devices (e.g., SDRAM, flash, NVRAM, EEPROM, and 
CPLD) wherever possible. There are no tests on 10G links. At this level, stack ports are shut 
down automatically.

level2

Enter the keyword 

level2

 to run Level 2 diagnostics. Level 2 diagnostics is a full set of 

diagnostic tests with no support for automatic partitioning. Level 2 diagnostics are used 
primarily for on-board loopback tests and more extensive component diagnostics. Various 
components on the board are put into loop back mode, and test packets are transmitted 
through those components. These diagnostics also perform snake tests using VLAN 
configurations. You must physically remove the unit from the stack to test 10G links.

verbose

Enter the keyword 

verbose

 to run the diagnostic in verbose mode. Verbose mode gives more 

information in the output than standard mode.

no-reboot

Enter the keyword 

no-reboot 

to avoid automatic rebooting of the chassis after completion of 

diagnostic execution. Generally, this option is never used because if you run the diagnostic 
once again without rebooting the chassis, it may cause an issue with the diagnostic results.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

number

Enter the stack unit number.

Range: 0 to 5

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

Samsung ML-2010 - B/W Laser Printer Manual preview
ML-2010 - B/W Laser Printer
Brand: Samsung Pages: 25
ABLELink ABLELink SE5002 Series Quick Start Manual preview
ABLELink SE5002 Series
Brand: ABLELink Pages: 4
QNAP TS-130-US User Manual preview
TS-130-US
Brand: QNAP Pages: 39
sysmik ICS-709 Installation Notes For Electrical Personnel preview
ICS-709
Brand: sysmik Pages: 2
Supero SUPERSERVER 6027R-TRF User Manual preview
SUPERSERVER 6027R-TRF
Brand: Supero Pages: 102
Moxa Technologies NPort P5250A Series Quick Installation Manual preview
NPort P5250A Series
Brand: Moxa Technologies Pages: 2
360 Systems MAXX-1200-HD Operation Manual preview
MAXX-1200-HD
Brand: 360 Systems Pages: 148
IBM System x3500 M2 Type 7839 Installation And User Manual preview
System x3500 M2 Type 7839
Brand: IBM Pages: 126
AIC FB128-LX User Manual preview
FB128-LX
Brand: AIC Pages: 79
Yawarra net5501 Quick Start Manual preview
net5501
Brand: Yawarra Pages: 4
Ekselans 280053 User Manual preview
280053
Brand: Ekselans Pages: 37
D-Link DVS-104 User Manual preview
DVS-104
Brand: D-Link Pages: 113
D-Link DVS-301 User Manual preview
DVS-301
Brand: D-Link Pages: 100
Planet FPS-1101 User Manual preview
FPS-1101
Brand: Planet Pages: 83
Polycom RSS 2000 V1.0 Getting Started Manual preview
RSS 2000 V1.0
Brand: Polycom Pages: 11
Lantronix CoBox-FL User Manual preview
CoBox-FL
Brand: Lantronix Pages: 135
B+B SmartWorx VESP211 Quick Start Manual preview
VESP211
Brand: B+B SmartWorx Pages: 2
GIGA-BYTE TECHNOLOGY G492-Z50 User Manual preview
G492-Z50
Brand: GIGA-BYTE TECHNOLOGY Pages: 141

Brands by name

Popular brands

Load more brands