Dell Force10 MXL Blade Reference Manual Download Page 132

Page: 132 / 732

132

Access Control Lists (ACL)

www.dell.com | support.dell.com

Route Map Commands

When an access-list is created without any rule and then applied to an interface, ACL behavior reflects
implicit permit.

The following commands allow you to configure route maps and their redistribution criteria.

•

continue

•

description

•

match interface

•

match ip address

•

match ip next-hop

•

match ip route-source

•

match metric

•

match route-type

•

match tag

•

route-map

•

set automatic-tag

•

set metric

•

set metric-type

•

set tag

•

show config

•

show route-map

continue

Configure a route-map to go to a route-map entry with a higher sequence number.

Syntax

continue

[

sequence-number

]

Parameters

Defaults

Not Configured

Command Modes

ROUTE-MAP

Command

History

Usage

Information

The

continue

feature allows movement from one route-map entry to a specific route-map entry (the

sequence number

). If you do not specify the sequence number, the

continue

feature simply moves to

the next sequence number (also known as an implied continue). If a match clause exists, the

continue

feature executes only after a successful match occurs. If there are no successful matches,

continue

ignored.

sequence-number

(OPTIONAL) Enter the route map sequence number.

Range: 1 - 65535

Default: no sequence number

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands