Dell Force10 MXL Blade Reference Manual Download Page 236

Page: 236 / 732

236

Interfaces

www.dell.com | support.dell.com

•

show config (from INTERFACE RANGE mode)

•

show interfaces

•

show interfaces configured

•

show interfaces dampening

•

show interfaces description

•

show interfaces stack-unit

•

show interfaces status

•

show interfaces switchport

•

show interfaces transceiver

•

show range

•

shutdown

•

speed (for 1000/10000/auto interfaces)

•

stack-unit portmode

clear counters

Clear the counters used in the

show interfaces

commands for all VRRP groups, VLANs, and physical

interfaces, or selected ones.

Syntax

clear counters

[

interface

] [

vrrp

[{

vrid

vrf

instance

}] |

learning-limit

]

Parameters

Defaults

Without a specific interface specified, the command clears all interface counters.

Command Modes

EXEC Privilege

Command

History

interface

(OPTIONAL) Enter any of the following keywords and slot/port or number to clear
counters from a specified interface:

•

For a Loopback interface, enter the keyword

loopback

followed by a number from

0 to 16383.

•

For a Port Channel interface, enter the keyword

port-channel

followed by a

number. Range: 1-128

•

For the management interface on the stack-unit, enter the keyword

managementethernet

followed by slot/port information. The slot range is 0-1,

and the port range is 0.

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

•

For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

followed by the

slot/port information.

•

For a VLAN, enter the keyword

vlan

followed by a number from 1 to 4094.

vrrp

[

vrid

]

(OPTIONAL) Enter the keyword

vrrp

to clear the counters of all VRRP groups. To

clear the counters of a specified group, enter a

vrid

number from 1 to 255.

vrrp

[

vrf

instance

]

(OPTIONAL): Enter the keyword

vrrp

to clear counters for all VRRP groups. To clear

the counters of VRRP groups in a specified VRF instance, enter the name of the
instance (32 characters maximum).

learning-limit

(OPTIONAL) Enter the keyword

learning-limit

to clear unknown source address (SA)

drop counters when MAC learning limit is configured on the interface.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands