Dell Force10 MXL Blade Reference Manual Download Page 74 | Manualshive

Page: 74 / 732

background image

74

|

Control and Monitoring

www.dell.com | support.dell.com

Figure 4-31.

show tech-support

Command Example (Partial)

Usage

Information

Without the

page or stack-unit

option, the command output is continuous, use

Ctrl-z

to interrupt the

command output.

The

save

option works with other filtering commands. This allows you to save specific information of

a show command. The

save

entry must always be the last option.

For example:

FTOS#

show tech-support |

grep

regular-expression

|

except

regular-expression

|

find

regular-expression | save flash://result

FTOS#show tech-support stack-unit 0
Required Type : -

-- Unit 5 --
Unit Type : Member Unit
Status : not present
Required Type : -

----------------------------------- show environment -------------------

-- Unit Environment Status --
Unit Status Temp Voltage
---------------------------------------------------------------------------
* 1 online 41C ok

* Management Unit

-- Thermal Sensor Readings (deg C) --
Unit Sensor0 Sensor1
---------------------------
1 39 41

----------------------------------- show ip traffic -------------------
IP statistics:
Rcvd: 894390 total, 415557 local destination
0 format errors, 0 checksum errors, 0 bad hop count
0 unknown protocol, 0 not a gateway
15 security failures, 0 bad options
Frags: 0 reassembled, 0 timeouts, 0 too big
0 fragmented, 0 couldn't fragment
Bcast: 402 received, 0 sent; Mcast: 37 received, 0 sent
Sent: 468133 generated, 0 forwarded
42 encapsulation failed, 0 no route

ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 2 unreachable
0 echo, 0 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 info request, 0 other
Sent: 0 redirects, 0 unreachable, 0 echo, 0 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp
0 info reply, 0 time exceeded, 0 parameter problem

UDP statistics:
Rcvd: 396516 total, 0 checksum errors, 0 no port
0 short packets, 0 bad length, 28746 no port broadcasts, 0 socket full
Sent: 16460 total, 28746 forwarded broadcasts

TCP statistics:
Rcvd: 4618 total, 0 checksum errors, 0 no port
Sent: 5023 total

ARP statistics:
Rcvd: 43988 requests, 24518 replies, 10 wrong interface
Sent: 42 requests, 6 replies (0 proxy)

«
...
72
73
74
75
76
...
»

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

RS/6000 7043 43P Series

Brand: IBM Pages: 322

System x3400 M3 Types 7378

Brand: IBM Pages: 45

8BIG RACK THUNDERBOLT 2

Brand: LaCie Pages: 28

Brand: IBM Pages: 200

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

Brand: IBM Pages: 220

PLATINIUM 9000-4R

Brand: MAXDATA Pages: 18

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

DPR-1260 - RangeBooster G Multifunction Print Server

Brand: D-Link Pages: 55

Brand: D-Link Pages: 49

TS-269L TurboNAS

Brand: QNAP Pages: 6

Brand: Grafenthal Pages: 99

Brand: Dataton Pages: 23

Brand: Kathrein Pages: 20

BTC14N-GP-TS20-DP-N0

Brand: Pepperl+Fuchs Pages: 41

Brand: CTC Union Pages: 40

Brand: IBM Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands