Dell Force10 MXL Blade Reference Manual Download Page 481

Page: 481 / 732

Quality of Service (QoS) |

481

show qos policy-map

View the QoS policy map information.

Syntax

show qos policy-map

{

summary

[

interface

]

detail

[

interface

]}

Parameters

Defaults

none

Command Modes

EXEC

EXEC Privilege

Command

History

Example 1

Figure 25-2. show qos policy-map detail (IPv4) Command Example

Example 2

Figure 25-3. show qos policy-map summary (IPv4) Command Example

summary

interface

To view a policy map interface summary, enter the keyword

summary

and

optionally one of the following keywords and slot/port or number information:

•

For a Forty Gigabit Ethernet interface, enter the keyword
Forty

GigabitEthernet

followed by the slot/port information.

•

For a Ten Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

detail

interface

To view a policy map interface in detail, enter the keyword

detail

and optionally

one of the following keywords and slot/port or number information:

•

For a FortyGigabit Ethernet interface, enter the keyword
Forty

GigabitEthernet

followed by the slot/port information.

•

For a Ten Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS#show qos policy-map detail tengigabitethernet 0/0

Interface TenGigabitEthernet 4/1

Policy-map-input policy
Trust diffserv
Queue# Class-map-name Qos-policy-name
0

CM1

CM2

CM3

FTOS#

FTOS#show qos policy-map summary

Interface policy-map-input policy-map-output
TenGig 4/1 PM1 -
TenGig 4/2 PM2

PMOut

FTOS#

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands