Dell Force10 MXL Blade Reference Manual Download Page 162 | Manualshive

Page: 162 / 732

background image

162

|

Data Center Bridging

www.dell.com | support.dell.com

Usage

Information

If you configure PFC on a 40GbE port, count the 40GbE port as four PFC-enabled ports in the

pfc-port

number you enter in the command syntax.

To achieve lossless PFC operation, the PFC port count and queue number used for the reserved buffer
size that is created must be greater than or equal to the buffer size required for PFC-enabled ports and
lossless queues on the switch.

You must reload the stack or a specified stack unit (use the

reload

command in EXEC Privilege mode)

for the PFC buffer configuration to take effect.

Related

Commands

dcbx port-role

Configure the DCBX port role used by the interface to exchange DCB information.

Syntax

dcbx port-role {config-source | auto-downstream | auto-upstream | manual}

To remove DCBX port role, use the

no dcbx port-role {config-source | auto-downstream |

auto-upstream | manual}

command.

Parameters

Defaults

Manual.

Command Modes

PROTOCOL LLDP

Command

History

Usage

Information

DCBX requires that you enable LLDP to advertise DCBX TLVs to peers.

Configure DCBX operation at the INTERFACE level on a switch. To verify the DCBX configuration
on a port, use the

show interface dcbx detail

command.

dcb stack-unit all pfc-buffering
pfc-port-count pfc-queues

Configure the PFC buffer for all switches in the stack.

config-source |
auto-downstream |
auto-upstream |
manual

Enter the DCBX port role, where:

•

config-source

: configures the port to serve as the configuration source on the

switch.

•

auto-upstream

: configures the port to receive a peer configuration. The

configuration source is elected from auto-upstream ports.

•

auto-downstream

: configures the port to accept the internally propagated

DCB configuration from a configuration source.

•

manual

: configures the port to operate only on administer-configured DCB

parameters. The port does not accept a DCB configuration received form a
peer or a local configuration source.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

«
...
160
161
162
163
164
...
»

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

eServer 130 xSeries

Brand: IBM Pages: 156

Brand: Raritan Pages: 99

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 12

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 16

IPedge EP Server

Brand: Toshiba Pages: 19

SD-H400 - Combination Progressive-Scan DVD Player

Brand: Toshiba Pages: 53

Brand: Toshiba Pages: 185

Digital Media Server

Brand: Toshiba Pages: 204

Brand: Toshiba Pages: 241

Brand: Toshiba Pages: 270

Brand: Toshiba Pages: 418

Brand: Toshiba Pages: 206

SG20 - Magnia - Web Server

Brand: Toshiba Pages: 331

Brand: Toshiba Pages: 335

Brand: Tekron Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands