Dell Force10 MXL Blade Reference Manual Download Page 101 | Manualshive

Page: 101 / 732

background image

Access Control Lists (ACL) |

101

Defaults

Not configured

Command Modes

CONFIGURATION-IP ACCESS-LIST-STANDARD

Command

History

Usage

Information

The

order

option is relevant in the context of the Policy QoS feature only. The following applies:

•

The

seq

sequence-number

is applicable only in an ACL group.

•

The

order

option works across ACL groups that have been applied on an interface via QoS policy

framework.

•

The

order

option takes precedence over the

seq

sequence-number

.

•

If

sequence-number

is

not

configured, then rules with the same order value are ordered

according to their configuration order.

•

If the

sequence-number

is configured, then the

sequence-number

is used as a tie breaker for

rules with the same order.

Related

Commands

source

Enter an IP address in dotted decimal format of the network from which the
packet was received.

mask

(OPTIONAL) Enter a network mask in /prefix format (/x) or A.B.C.D. The
mask, when specified in A.B.C.D format, may be either contiguous or
non-contiguous.

any

Enter the keyword

any

to specify that all routes are subject to the filter.

host

ip-address

Enter the keyword

host

followed by the IP address to specify a host IP address

or hostname.

count

(OPTIONAL) Enter the keyword

count

to count packets processed by the

filter.

byte

(OPTIONAL) Enter the keyword

byte

to count bytes processed by the filter.

dscp

(OPTIONAL) Enter the keyword

dscp

to match to the IP DSCP values.

order

(OPTIONAL) Enter the keyword

order

to specify the QoS order for the ACL

entry.

Range:

0-254 (where 0 is the highest priority and 254 is the lowest; lower

order numbers have a higher priority)

Default:

If the order keyword is not used, the ACLs have the lowest order by
default (255).

fragments

Enter the keyword

fragments

to use ACLs to control packet fragments.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

deny

Configures a filter to drop packets.

permit

Configures a filter to forward packets.

seq

Assigns a sequence number to a deny or permit filter in an IP access list while creating the

filter.

«
...
99
100
101
102
103
...
»

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

Brand: Samsung Pages: 7

Brand: Qlogic Pages: 20

Brand: Supero Pages: 112

Brand: ACTi Pages: 15

Brand: ioCorp Pages: 18

Brand: IBM Pages: 44

Brand: Conceptronic Pages: 127

Brand: HIKVISION Pages: 13

ANR-C62-N1 Series

Brand: Acrosser Technology Pages: 57

Netfinity Series

Brand: IBM Pages: 44

DPR-1260 - RangeBooster G Multifunction Print Server

Brand: D-Link Pages: 55

Brand: D-Link Pages: 49

StorageWorks E Series

Brand: HP Pages: 8

StorageWorks 9000s NAS

Brand: HP Pages: 7

StorageWorks NAS e7000 v2

Brand: HP Pages: 2

StorageWorks NAS e7000 v2

Brand: HP Pages: 70

StorageWorks 600 All-in-One

Brand: HP Pages: 58

StorageWorks All-in-One SB600c - Storage Blade

Brand: HP Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands