Dell Force10 MXL Blade Reference Manual Download Page 640

Page: 640 / 732

640

System Time and Date

www.dell.com | support.dell.com

Command Modes

CONFIGURATION

Command

History

Usage

Information

You can configure multiple time serving hosts (up to 250). From these time serving hosts, the FTOS

chooses one NTP host with which to synchronize. To determine which server was selected, use the

show ntp associations

Because a large number of polls to NTP hosts can impact network performance, Dell Force10
recommends limiting the number of hosts configured.

Related

Commands

ntp source

Specify an interface’s IP address to be included in the NTP packets.

Syntax

ntp source

interface

To delete the configuration, use the

no ntp source

command.

Parameters

Defaults

Not configured.

Command Modes

CONFIGURATION

Command

History

ntp trusted-key

Set a key to authenticate the system to which NTP will synchronize.

Syntax

ntp trusted-key

number

To delete the key, use the

no ntp trusted-key

number

command.

Parameters

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

show ntp associations

Displays NTP servers configured and their status.

interface

Enter the following keywords and slot/port or number information:

•

For Loopback interfaces, enter the keyword

loopback

followed by a number from

zero (0) to 16383.

•

For a Port Channel interface, enter the keyword

lag

followed by a number:

Range: 1-128

•

For a 10-Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed

by the slot/port information.

•

For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

followed by the

slot/port information.

•

For VLAN interface, enter the keyword

vlan

followed by a number from 1 to 4094.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

number

Enter a number as the trusted key ID.

Range: 1 to 4294967295.

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands