Dell Force10 MXL Blade Reference Manual Download

Page: 484 / 732

484

Quality of Service (QoS)

www.dell.com | support.dell.com

Example

Figure 25-7. show qos qos-policy-output Command Example

show qos statistics

View QoS statistics.

Syntax

show qos statistics

{

wred-profile

[

interface

]} | [

interface

]

Parameters

Defaults

none

Command Modes

EXEC

EXEC Privilege

Command

History

Example 1

Figure 25-8. show qos statistics Command Example

FTOS#show qos qos-policy-output

Qos-policy-output qmap_out
Bandwidth-percentage 10

Qos-policy-output qmap_wg
Rate-shape 100 50
Wred yellow wy
Wred green wg
FTOS#

wred-profile

interface

Enter the keyword

wred-profile

and optionally one of the following

keywords and slot/port or number information:

•

For a Forty Gigabit Ethernet interface, enter the keyword

FortyGigabitEthernet

followed by the slot/port information.

•

For a Ten Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

interface

Enter one of the following keywords and slot/port or number information

•

For a Forty Gigabit Ethernet interface, enter the keyword
Forty

GigabitEthernet

followed by the slot/port information.

•

For a Ten Gigabit Ethernet interface, enter the keyword

TenGigabitEthernet

followed by the slot/port information.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS#show qos statistics
Interface Te 0/20
Queue# Matched Pkts
0 0
1 0
2 0
3 0
FTOS#

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands

Dell Force10 MXL Blade, Reference Manual

Search results

Summary of Contents for Force10 MXL Blade

Reviews:

Related manuals for Force10 MXL Blade

Brands by name

Popular brands