manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 227

Internet Group Management Protocol (IGMP) |

227

13

Internet Group Management Protocol (IGMP)

IGMP Snooping Commands

The Dell Force10 operating software (FTOS) supports internet group management protocol (IGMP) 
snooping version 2 and 3 on all Dell Force10 systems:

•

ip igmp access-group

•

ip igmp group-join-limit

•

ip igmp querier-timeout

•

ip igmp query-interval

•

ip igmp query-max-resp-time

•

ip igmp version

•

ip igmp snooping enable

•

ip igmp snooping fast-leave

•

ip igmp snooping flood

•

ip igmp snooping last-member-query-interval

•

ip igmp snooping mrouter

•

ip igmp snooping querier

•

show ip igmp snooping mrouter

Important Points to Remember for IGMP Snooping 

•

FTOS supports version 1, version 2, and version 3 hosts.

•

FTOS IGMP snooping implementation is based on IP multicast address (not based on Layer 2 
multicast mac-address) and the IGMP snooping entries are in Layer 3 flow table not in Layer 2 
forwarding information base (FIB).

•

FTOS IGMP snooping implementation is based on draft-ietf-magma-snoop-10.

•

IGMP snooping is supported on all MXL 10/40GbE stack members.

•

IGMP snooping is not enabled by default on the switch.

•

A maximum of 1800 groups and 600 virtual local area network (VLAN) are supported.

•

IGMP snooping is not supported on default VLAN interface.

•

IGMP snooping is not supported over VLAN-Stack-enabled VLAN interfaces (you must disable 
IGMP snooping on a VLAN interface before configuring VLAN-Stack-related commands).

•

IGMP snooping does not react to Layer 2 topology changes triggered by spanning tree protocol 
(STP).

•

IGMP snooping reacts to Layer 2 topology changes triggered by multiple spanning tree protocol 
(MSTP) by sending a general query on the interface that comes in FWD state.

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands