manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 168

168

|

Data Center Bridging

www.dell.com | support.dell.com

Defaults

none

Command Modes

DCB INPUT POLICY

Command

History

Usage

Information

you can enable any number of 802.1p priorities for PFC. Queues to which PFC priority traffic is 
mapped are lossless by default. Traffic may be interrupted due to an interface flap (going down and 
coming up) when you reconfigure the lossless queues for no-drop priorities in a PFC input policy and 
re-apply the policy to an interface.

The maximum number of lossless queues supported on the switch is two. 

The configured priority traffic must be supported by a PFC peer (as detected by DCBX) for PFC to be 
applied.

Related

Commands

priority-group

Create an ETS priority group to use with an ETS output policy.

Syntax

priority-group 

group-name

To remove the priority group, use the 

no priority-group 

command.

Parameters

 

Defaults

none

Command Modes

CONFIGURATION

Command

History

Usage

Information

A priority group consists of 802.1p priority values that are grouped together for similar bandwidth 

allocation and scheduling, and that share the same latency and loss requirements. All 802.1p priorities 
mapped to the same queue should be in the same priority group. 

All 802.1p priorities should be configured in priority groups associated with an ETS output policy. You 

can assign each dot1p priority to only one priority group. 

The maximum number of priority groups supported in ETS output policies on an interface is equal to 
the number of data queues (4) on the port. The 802.1p priorities in a priority group can map to multiple 
queues.

If you configure more than one priority queue as strict priority or more than one priority group as strict 
priority, the higher numbered priority queue is given preference when scheduling data traffic

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

dcb-input

Create a DCB input policy.

group-name

Enter the name of the ETS priority group. Maximum: 32 characters.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands