manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 458

458

|

Per-VLAN Spanning Tree Plus (PVST+)

www.dell.com | support.dell.com

tc-flush-standard 

Enable the MAC address flushing upon receiving every topology change notification.

Syntax

tc-flush-standard

 

To disable, use the 

no tc-flush-standard

 command.

Defaults

Disabled

Command Modes

CONFIGURATION

Command

History

Usage

Information

By default FTOS implements an optimized flush mechanism for PVST+. This helps in flushing the 
MAC addresses only when necessary (and less often) allowing for faster convergence during topology 
changes. However, if a standards-based flush mechanism is needed, this 

knob

 command can be turned 

on to enable flushing MAC addresses upon receiving every topology change notification.

vlan bridge-priority 

Set the PVST+ bridge-priority for a VLAN or a set of VLANs.

Syntax

vlan 

<vlan-id> 

bridge-priority

 value 

To return to the default value, enter 

no vlan bridge-priority

 

command.

Parameters

 

Defaults

32768

Command Modes

CONFIGURATION (conf-pvst)

Command

History

Related

Commands

 

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

vlan 

vlan-range

Enter the keyword 

vlan

 followed by the VLAN number(s).

Range: 1 to 4094

bridge-priority 

value

Enter the keyword 

bridge-priority 

followed by the bridge priority value in 

increments of 4096. 

Range: 0 to 61440

Default: 32768

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

vlan forward-delay

Change the time interval before FTOS transitions to the forwarding state

vlan hello-time

Change the time interval between BPDUs

vlan max-age

Change the time interval before PVST+ refreshes

show spanning-tree pvst

Display the PVST+ configuration

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands