manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

The Dell Force10 MXL Blade is a cutting-edge network switch designed for high-performance data centers. Unlock its full potential by easily configuring its advanced features through our comprehensive and user-friendly manual, available for free download at manualshive.com. Empower your network infrastructure today with this unparalleled product.

Share
Download
background image

CLI Basics |

17

EXEC Privilege Mode 

The 

enable

 

command accesses EXEC Privilege mode. If an administrator has configured an 

Enable

 

password, you are prompted to enter the password here.

EXEC Privilege mode allows you to access all commands accessible in EXEC mode, plus other 
commands, such as to clear ARP entries and IP addresses. In addition, you can access 
CONFIGURATION mode to configure interfaces, routes, and protocols on the switch. While you are 
logged in to EXEC Privilege mode, the

 # 

prompt displays.

CONFIGURATION Mode

In EXEC Privilege mode, use the 

configure

 command to enter CONFIGURATION mode and 

configure routing protocols and access interfaces.

To enter CONFIGURATION mode:

1.

Verify that you are logged in to EXEC Privilege mode.

2.

Enter the 

configure

 

command. The prompt changes to include (conf). 

From this mode, you can enter INTERFACE mode by using the 

interface

 command.

INTERFACE Mode

Use INTERFACE mode to configure interfaces or IP services on those interfaces. An interface can be 
physical (for example, a TenGigabit Ethernet port) or virtual (for example, the Null interface). 

To enter INTERFACE mode:

1.

Verify that you are logged into CONFIGURATION mode.

2.

Enter the 

interface

 command followed by an interface type and interface number that is available 

on the switch. 

3.

The prompt changes to include the designated interface and slot/port number (

Table 2-3

). 

Table 2-3.  Interface prompts

Prompt

Interface Type

FTOS(conf-if)#

INTERFACE mode

FTOS(conf-if-te-0/0)#

Ten Gigabit Ethernet interface followed by slot/port information

FTOS(conf-if-fo-0/0)#

Forty Gigabit Ethernet interface followed by slot/port information

FTOS(conf-if-lo-0)#

Loopback interface number. 

FTOS(conf-if-nu-0)#

Null Interface followed by zero

FTOS(conf-if-po-1)#

Port-channel interface number

FTOS(conf-if-vl-1)#

VLAN Interface followed by VLAN number (range 1 to 4094)

FTOS(conf-if-ma-0/0)#

Management Ethernet interface followed by slot/port information

FTOS(conf-if-range)#

Designated interface range (used for bulk configuration; refer to 

interface 

range

).

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

LaCie 2big Network 2 Datasheet preview
2big Network 2
Brand: LaCie Pages: 4
Yamaha MCX-2000 - MusicCAST Digital Audio Server Owner'S Manual Addendum preview
MCX-2000 - MusicCAST Digital Audio Server
Brand: Yamaha Pages: 25
Avaya 2N Helios IP Application Notes preview
2N Helios IP
Brand: Avaya Pages: 19
IBM x3350 - System - 4192 User Manual preview
x3350 - System - 4192
Brand: IBM Pages: 98
IBM x3500 - System - 7977 Installation Manual preview
x3500 - System - 7977
Brand: IBM Pages: 124
IBM System x3250 Installation And User Manual preview
System x3250
Brand: IBM Pages: 106
IBM x3200 - System M3 - 7328 Installation Manual preview
x3200 - System M3 - 7328
Brand: IBM Pages: 100
IBM System x3400 Type 7975 Installation Manual preview
System x3400 Type 7975
Brand: IBM Pages: 124
IBM System x3300 M4 Installation And Service Manual preview
System x3300 M4
Brand: IBM Pages: 470
IBM System x iDataPlex dx360 Manual preview
System x iDataPlex dx360
Brand: IBM Pages: 26
Bosch DL380 Gen 10 AI Quick Installation Manual preview
DL380 Gen 10 AI
Brand: Bosch Pages: 18
Bosch DIP-61F0-00N Installation Manual preview
DIP-61F0-00N
Brand: Bosch Pages: 48
Bosch PRA-APAS Configuration Manual preview
PRA-APAS
Brand: Bosch Pages: 44
D-Link DP-100 Hardware User'S Manual preview
DP-100
Brand: D-Link Pages: 32
D-Link DP-101 Hardware Manual preview
DP-101
Brand: D-Link Pages: 22
D-Link DP-313 - Air 802.11b Wireless Print Server User Manual preview
DP-313 - Air 802.11b Wireless Print Server
Brand: D-Link Pages: 28
D-Link DP 301U Quick Installation Manual preview
DP 301U
Brand: D-Link Pages: 64
D-Link D DP-301P+ DP-301P+ Datasheet preview
D DP-301P+ DP-301P+
Brand: D-Link Pages: 2

Brands by name

Popular brands

Load more brands