Dell Force10 MXL Blade Reference Manual Download | Manualshive

Page: 498 / 732

background image

498

|

Routing Information Protocol (RIP)

www.dell.com | support.dell.com

Related

Commands

ip split-horizon

Enable split-horizon for RIP data on the interface. As described in RFC 2453, the split-horizon scheme
prevents any routes learned over a specific interface to be sent back out that interface.

Syntax

ip split-horizon

To disable split-horizon, enter

no ip split-horizon.

Defaults

Enabled

Command Modes

INTERFACE

Command History

Related

Commands

maximum-paths

Set RIP to forward packets over multiple paths.

Syntax

maximum-paths

number

To return to the default values, use the

no maximum-paths

command.

Parameters

Defaults

4

Command Modes

ROUTER RIP

Command

History

Usage

Information

RIP supports a maximum of 16 ECMP paths.

neighbor

Define a neighbor router with which to exchange RIP information.

Syntax

neighbor

ip-address

To delete a neighbor setting, use the

no neighbor

ip-address

command.

ip rip receive version

Sets the RIP version for the interface to receive traffic.

version

Sets the RIP version to be used for the switch software.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

ip poison-reverse

Sets the prefix for RIP routing updates.

number

Enter the number of paths.

Range: 1 to 16.

The default is 4 paths.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

«
...
496
497
498
499
500
...
»

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Force10 MXL Blade

Brand: Hanwha Pages: 3

Brand: IBM Pages: 92

Brand: MSI Pages: 107

UniServer T1100 G3

Brand: H3C Pages: 138

Netfinity 1000-8477 21Y

Brand: IBM Pages: 268

Brand: TYANO Pages: 102

eserver iSeries 270

Brand: IBM Pages: 40

Connectware PortServer TS 8/16

Brand: Digi Pages: 106

Brand: NEC Pages: 10

Brand: NEC Pages: 20

Brand: NEC Pages: 2

Brand: NEC Pages: 18

Brand: NEC Pages: 2

Care Standard/300

Brand: NEC Pages: 11

Brand: NEC Pages: 88

Brand: NEC Pages: 89

Brand: NEC Pages: 62

Express 5800/120Ed

Brand: NEC Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands