manualshive.com logo in svg

Dell Force10 MXL Blade, Reference Manual

Share
Download
Dell Force10 MXL Blade Reference Manual Download Page 245

Interfaces |

245

The Management port is enabled by default (no 

shutdown

). Use the 

ip address

 command to assign an 

IP address to the Management port.

Related

Commands

interface null

Configure a Null interface on the switch.

Syntax

interface null 

number

Parameters

 

Defaults

Not configured; 

number

 = 0

Command Modes

CONFIGURATION

Command

History

Example

Figure 14-10.  interface null Command Example 

Usage

Information

You cannot delete the Null interface. The only configuration command possible in a Null interface is 

ip 

unreachables

.

Related

Commands

 

interface range

This command permits configuration of a range of interfaces to which subsequent commands are 
applied (bulk configuration). Using the 

interface range

 command, you can enter identical commands 

for a range of interface.

Syntax

interface range 

interface

, 

interface

,.

..

management route

Configure a static route that points to the Management interface or a 
forwarding router.

duplex (1000/10000 Interfaces)

Configure duplex mode on any physical interfaces where the speed is set 
to 1000/10000

number

Enter zero (0) as the Null interface number.

Version 8.3.16.1

Introduced on MXL 10/40GbE Switch IO Module

FTOS(conf)#interface null 0
FTOS(conf-if-nu-0)#

interface

Configures a physical interface.

interface loopback

Configures a Loopback interface.

interface port-channel

Configures a port channel.

interface vlan

Configures a VLAN.

ip unreachables

Enables generation of ICMP unreachable messages.

Summary of Contents for Force10 MXL Blade





























































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands